Setting Wan Properties Using The Wan Properties Screen; Setting Port Properties Using The Port Properties Screen - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Related
Documentation
Setting WAN Properties Using the WAN Properties Screen
Related
Documentation
Setting Port Properties Using the Port Properties Screen
54
Deny routing to this interface.
Routing to ACVPN-dynamic.
On ADSL interfaces, you can configure ADSL options such as VPI and VCI, multiplexing
mode as part of the General Properties. See "ADSL Interface in ScreenOS Devices" on
page 88.
On wireless interfaces, you also shut down the interface by selecting the Shutdown
Interface option.
Some interfaces, such as the VLAN1 or serial interface, accept service option settings as
part of the General Properties for the interface. For information about service options,
see "Enabling Management Service Options for Interfaces" on page 56.
Configuring Physical and Function Zone Interfaces in ScreenOS Devices Overview on
page 52
Setting Physical Link Attributes for Interfaces on page 55
Use the WAN Properties screen to configure the following WAN properties for port cards
on available devices:
Clocking
Hold time (Up)
Hold time (Down)
For more information about configuring WAN properties for port cards, refer to the
ScreenOS Wide Area Network Interfaces and Protocols Reference.
Setting Interface Properties Using the General Properties Screen on page 53
Setting Port Properties Using the Port Properties Screen on page 54
Using MLFR and MLPPP Options on page 55
Use the Port Properties screen to configure the following properties for port cards on
available devices:
Port Configuration (Serial, E1, T1, or DS3)
DCE options
DTE options
Line encoding
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?