Configuring Acceptable Groups (Nsm Procedure) - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Related
Documentation
Configuring Acceptable Groups (NSM Procedure)
Copyright © 2010, Juniper Networks, Inc.
In the virtual router navigation tree, select Dynamic Routing Protocol.
Select the Configure PIM-SM check box. PIM-SM configuration options now appear
in the virtual router navigation tree under Dynamic Routing Protocol.
In the virtual router navigation tree, select Dynamic Routing Protocol > PIM-SM >
Rendezvous Points.
Click the Add icon. The new Zone dialog box appears. For Zone, select the zone that
contains the RP.
Configure a C-RP:
3.
Select the interface that is advertised as the C-RP.
Specify the access list that identifies the multicast group(s) for which the interface
is the RP candidate.
Select the advertised C-RP priority.
Select the holdtime advertised to the bootstrap router.
Configure a static rendezvous point:
4.
Click the Add icon in the Static RP Addresses area. The Static RP Addresses dialog
box appears.
Enter the IP address of the RP.
Specify the access list that identifies the multicast group(s) mapped to the RP.
If you want to always use the same RP for the specified multicast group(s), select
the Always used as RP check box. Use this option to override dynamic group-RP
mappings.
Click OK to save your changes to the virtual router, and then click OK to save your
5.
changes to the device configuration.
Access List Overview on page 298
Multicast Route Overview on page 337
Configuring IGMP (NSM Procedure) on page 338
Configuring IGMP Proxy (NSM Procedure) on page 339
Configuring PIM Sparse Mode (NSM Procedure) on page 341
Configuring Acceptable Groups (NSM Procedure) on page 343
You can create access lists to identify the acceptable sources, multicast groups, and
RPs, and then configure the virtual router to accept PIM messages only from those
specified in the access lists.
Chapter 10: Routing
343
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?