Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual page 288
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
264
Click OK to save the slot configuration.
Create the vsys music. In the Device Manager, select Security Devices, and then
double-click the vsys music to open the vsys configuration.
Create two custom Layer 2 zones on the vsys music:
2.
In the vsys configuration tree, select Network > Zones. Click the Add icon and select
Security Zone. Configure the zone name as music-trust, and then click OK.
In the vsys configuration tree, select Network > Zones. Click the Add icon and select
Security Zone. Configure the zone name as music-untrust, and then click OK.
Import VLAN IDs from the root system to the vsys music:
3.
In the vsys navigation tree, select Network > Vlan > Import.
Click the Add icon to display the New VLAN Import Entry. Configure the following
settings, and then click OK:
For Vlan ID Begin, enter 100.
For Vlan ID End, enter 199.
For Comments, enter music vlans.
Create a VLAN group on the vsys music. In the vsys navigation tree, select Network
> Vlan > Group, and then click the Add icon to display the New VLAN Group Entry.
Configure the following setting:
For Vlan Group Name, enter it_music.
In the Setting Vlan Group area, click the Add icon to display the New Vlan Group
4.
Range. Configure the following settings, and then click OK:
For Start Vlan ID, enter 100.
For End Vlan ID, enter 199.
In the Binding Vlan Group to Port and Zone area, click the Add icon to display the New
5.
Vlan Group Port Settings. Configure the following settings, and then click OK.
For Interface, select ethernet2/5.
For Zone, select music-trust.
In the Binding Vlan Group to Port and Zone area, click the Add icon to display the New
6.
Vlan Group Port Settings. Configure the following settings, and then click OK.
For Interface, select ethernet2/1.
For Zone, select music-untrust.
Create management interface for vsys music:
In the vsys navigation tree, select Network > Interfaces, and then click the Add icon
and select VLAN Interface.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5