Configuring A Bgp Routing Instance (Nsm Procedure) - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring a BGP Routing Instance (NSM Procedure)
Related
Documentation
Copyright © 2010, Juniper Networks, Inc.
To configure BGP:
In the NSM navigation tree, select Device Manager > Devices. Double-click the device
1.
object to open the device configuration.
In the device navigation tree, select Network >Virtual Router to display the list of
2.
configured virtual routers. Double-click the virtual router in which you are configuring
a BGP routing instance. The Virtual Router configuration screen appears.
In the virtual router navigation tree, select Dynamic Routing Protocol and enable
3.
Configured BGP Instance check box. BGP configuration options now appear in the
virtual router navigation tree under Dynamic Routing Protocol.
In the virtual router navigation tree, select BGP > Parameters to display the Parameters
4.
screen. Configure the following:
Select the Enable BGP check box.
Enter an AS Number.
In the virtual router navigation tree, select BGP > Neighbors to display the Neighbors
5.
screen. Click the Add icon to display the New Neighbor screen. Configure the following:
Select the Peer Enabled check box.
Enter the BGP peer information.
Click OK to save the new neighbor.
6.
Click OK to save your changes to the virtual router.
7.
In the device navigation tree, select Network > Interface to display the list of interfaces.
8.
Double-click the interface that is connected to the BGP peer to open the interface
screen.
In the interface navigation tree, select Protocol to display the Protocol screen, and
9.
then click the BGP tab and enable BGP check box.
Click OK.
10.
BGP Overview on page 327
Route-Refresh Capabilities Overview on page 328
Multicast Route Overview on page 337
Configuring Neighbors and Peer Groups Overview on page 330
Configuring BGP Networks on page 329
Configuring Aggregate Addresses on page 329
Chapter 10: Routing
331
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?