Source-Based Routes Overview; Example: Configuring Source-Based Routes (Nsm Procedure) - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Source-Based Routes Overview
Related
Documentation
Example: Configuring Source-Based Routes (NSM Procedure)
308
Virtual Router General Properties Overview on page 297
Access List Overview on page 298
Route Maps Overview on page 300
Routing Table Entries Overview on page 305
Source-Based Routes Overview on page 308
Some security devices also enable you to configure a route entry based on the source IP
address of the data packet.
To create a static route for a network destination, you must enter the IP address and
netmask for the destination network, then select the interface through which the next
hop router is accessed. You must also enter the IP address of the next hop router and
configure a metric for the route.
For instructions for configuring virtual router source-based route entries, see the Network
and Security Manager Online Help.
Route Types Overview on page 295
Virtual Routers Overview on page 296
Virtual Router General Properties Overview on page 297
Access List Overview on page 298
Route Maps Overview on page 300
Routing Table Entries Overview on page 305
In this example, you want to forward traffic from the 10.1.1.0/24 subnetwork to ISP 1, and
forward traffic from the 10.1.2.0/24 subnetwork to ISP 2. You must configure two entries
in the default trust-vr routing table and enable source-based routing. The subnetwork
10.1.1.0/24, with ethernet1 as the forwarding interface, uses the ISP 1 router (1.1.1.1) as the
next hop; subnetwork 10.1.2.0/24, with ethernet2 as the forwarding interface, uses the
ISP 2 router (2.2.2.2) as the next hop.
In the NSM navigation tree, select Device Manager > Devices. Double-click the device
1.
object to open the device configuration.
In the device navigation tree, select Network > Virtual Routers. Double-click the
2.
trust-vr virtual router. The General Properties screen appears.
In the virtual router navigation tree, select Routing Table.
3.
Select Enable Source-Based Routing.
4.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?