Configuring Route Preferences - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Related
Documentation
Configuring Route Preferences
Related
Documentation
312
Configure the first entry. In the Source Interface-Based Routing Table area, click the
7.
Add icon.
Configure the following options:
8.
For Incoming Interface, select ethernet2/1.
For IP Address and Netmask, enter 10.1.1.0/24
For Interface, enter ethernet2/3.
For Gateway IP Address, enter 1.1.1.1
Click OK to save the SIBR entry.
Configure the second entry. In the Source Interface-Based Routing Table area, click
9.
the Add icon.
Configure the following:
10.
For Incoming Interface, select ethernet2/3.
For IP Address and Netmask, enter 10.1.2.0/24
For Interface, enter ethernet2/4.
For Gateway IP Address, enter 2.2.2.2
Click OK to save the SIBR entry.
Click OK to save your changes to the virtual router, and then click OK to save your
11.
changes to the device.
Destination-Based Routes Overview on page 307
Source-Based Routes Overview on page 308
A route preference is a weight added to the route that influences the determination of
the best path for traffic to reach its destination. When importing or adding a route to the
routing table, the virtual router adds a preference value—determined by the protocol by
which the route is learned—to the route. A low preference value (a number closer to 0)
is preferable to a high preference value (a number further from 0). In a virtual router, you
can set the preference value for routes according to protocol.
To change the preference value for a protocol, enter a new value for the protocol in the
Route Preferences configuration screen.
Route Types Overview on page 295
Access List Overview on page 298
Route Maps Overview on page 300
Routing Table Entries Overview on page 305
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?