Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual page 107
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
Ensure that Manageable is enabled.
Ensure that the Management IP is 210.1.1.1.
Add ethernet1/1 as a member of the redundant1 interface:
6.
In the cluster navigation tree, select Network > Interface. Double-click ethernet1/1.
The General Properties screen appears.
Configure the Redundant Interface Group as redundant1, and then click OK to save
your changes.
Add ethernet1/2 as a member of the redundant1 interface:
7.
In the cluster navigation tree, select Network > Interface. Double-click ethernet1/1.
The General Properties screen appears.
Configure the Redundant Interface Group as redundant1, and then click OK to save
your changes.
Configure the redundant2 interface:
8.
In the cluster navigation tree, select Network > Interface.
Click the Add icon and select Redundant Interface. The General Properties screen
appears.
Configure the following options, and then click OK:
9.
For Zone, select Trust.
For IP address/netmask, enter 10.1.1.1/24.
Add ethernet2/1 as a member of the redundant2 interface:
10.
In the cluster navigation tree, select Network > Interface. Double-click ethernet1/1.
The General Properties screen appears.
For Redundant Interface Group, select redundant2.
Click OK to save your changes.
Add ethernet2/2 as a member of the redundant2 interface:
11.
In the cluster navigation tree, select Network > Interface. Double-click ethernet1/1.
The General Properties screen appears.
For Redundant Interface Group, select redundant2.
Click OK to save your changes.
Add the VSI interface for redundant1:
12.
In the cluster navigation tree, select Network > Interfaces. Click the Add icon and
select VSI. The General Properties screen appears.
Configure the following options, and then click OK:
13.
For Name, select redundant1, and then select 1 (for VSD Group 1).
Chapter 3: Network Settings
83
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5