Configuring Neighbors And Peer Groups Overview - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Table 80: Aggregate Address
Parameters
AS Set
Summary Only
Route Maps (ScreenOS 5.1 and later only)
Related
Documentation
Configuring Neighbors and Peer Groups Overview
Related
Documentation
330
For each aggregate address you want to use, create an aggregate address entry that
contains the aggregate address IP and netmask. Next, configure the route attributes for
the address. The aggregate address configuration details are displayed in Table 80 on
page 330.
Your Action
When enabled, BGP generates AS set-path information for the aggregated
route and all contributing routes.
When enabled, BGP advertises the aggregate route in place of individual
addresses for more specific contributing routes. If you select this option, you
cannot configure a Suppress Route Map entry for this aggregate route.
Configure a previously created route map for each of the following:
Advertise Route Map—Select the previously created route map that defines
the path attributes for the aggregate route.
Attribute Route Map—Select the previously created route map that defines
the route attributes for the aggregate route.
Suppress Route Map—Select the previously created route map that you
want BGP to suppress for the aggregate route. If you select this option, you
cannot enable Summary Only for this aggregate route.
BGP Overview on page 327
Route-Refresh Capabilities Overview on page 328
Configuring BGP Networks on page 329
Configuring Neighbors and Peer Groups Overview on page 330
Configuring a BGP Routing Instance (NSM Procedure) on page 331
Use the Neighbor settings to configure individual peer addresses, called neighbors. You
can also assign neighbors to a peer-group to configure parameters for the peer-group as
a whole (you cannot assign IBGP and EBGP peers to the same peer-group).
BGP Overview on page 327
Route-Refresh Capabilities Overview on page 328
Configuring BGP Networks on page 329
Configuring Aggregate Addresses on page 329
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?