Device Level L2Tp Vpn: Using L2Tp Users Configuration Overview; Device Level L2Tp Vpn: Using L2Tp Configuration Overview - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Related
Documentation
Device Level L2TP VPN: Using L2TP Users Configuration Overview
Related
Documentation
Device Level L2TP VPN: Using L2TP Configuration Overview
Table 60: Device Level L2TP VPN: using L2TP Configuration
L2TP Options
Description
Host Name
Enter the name of the L2TP host.
Copyright © 2010, Juniper Networks, Inc.
Device Level L2TP VPN: Using L2TP Users Configuration Overview on page 235
Device Level L2TP VPN: Using L2TP Configuration Overview on page 235
Device-Level Manual Key VPN: Using VPN Configuration Overview on page 232
Creating device-level L2TP VPN is a three stage process.
Add L2TP Users
Configure L2TP Settings
Add VPN rules to Security Policy
For VPNs that use L2TP to provide remote access services, you must add an L2TP user
to the security device. An L2TP User has an account on the security device that guards
the protected resources in the VPN; when the user attempts to connect to a protected
resource, the security device authenticates the user.
To add a L2TP user for a security device, in the security device configuration
L2TP/XAuth/Local User, click the Add icon. Enter a name for the user, and then specify:
User—Select a preconfigured local user object that is configured for L2TP.
Remote Setting—Select a preconfigured remote settings object.
IP Pool—Select a preconfigured IP pool object.
Static IP—Enter the static IP address of the local user.
Device Level L2TP VPN: Using L2TP Configuration Overview on page 235
Device Level L2TP VPN: Using VPN Rule Configuration Overview on page 236
Device Level Manual Key VPN: Using VPN Rule Configuration Overview on page 234
To connect to an L2TP VPN tunnel, the L2TP RAS user uses the IP address and WINS/DNS
information assigned by the user's ISP. However, when the L2TP RAS user sends VPN
traffic through the tunnel, the security device assigns a new IP address and WINS/DNS
information that enables the traffic to reach the destination network.
Enter a name for the L2TP VPN, and then specify the following information as described
in Table 60 on page 235.
Chapter 8: Configuring VPNs
235
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?
Questions and answers