Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual page 393
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
For IP address and netmask, enter 210.1.1.1/24.
Click OK to save your changes.
Configure the Trust interface for the cluster:
9.
In the cluster navigation tree, select Network > Interface. Double-click ethernet3.
The General Properties screen appears.
For Zone, select Trust.
For IP address and netmask, enter 10.1.1.1/24.
Ensure that the interface mode is NAT, and then click OK to save your changes.
Click Apply to apply all previous changes to the cluster members.
10.
Configure the Manage IP and Monitoring for Corporate A:
11.
In the cluster navigation tree, select Members. Double-click Corporate A to open
its device configuration.
In the device navigation tree, select Network > Interface and double-click ethernet
3. The General Properties screen appears.
For Manage IP, enter 10.1.1.20, and then click OK to save your changes.
In the device navigation tree, select Monitoring > Whole Box Monitoring, and then
12.
select the Monitor Interface tab.
Click the Add icon to display the new monitor interface dialog box. Select ethernet1,
13.
leave the default weight of 255, and click OK to save your changes.
Click the Add icon to display the new monitor interface dialog box. Select ethernet3,
14.
leave the default weight of 255, and click OK to save your changes.
Click OK to close the device configuration for Corporate A.
15.
Configure the Manage IP for Corporate B:
16.
In the cluster navigation tree, select Members. Double-click Corporate B to open
its device configuration.
In the device navigation tree, select Network > Interface and double-click ethernet
3. The General Properties screen appears.
For Manage IP, enter 10.1.1.21, and `then click OK to save your changes.
In the device navigation tree, select Monitoring > Whole Box Monitoring, and then
select the Monitor Interface tab.
Click the Add icon to display the new monitor interface dialog box. Select ethernet1,
leave the default weight of 255, and click OK to save your changes.
Click the Add icon to display the new monitor interface dialog box. Select ethernet3,
leave the default weight of 255, and click OK to save your changes.
Click OK to close the device configuration for Corporate B.
Chapter 13: High Availability
369
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5