Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual page 368
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Related
Documentation
344
To configure acceptable groups on the virtual router:
In the NSM navigation tree, select Device Manager > Devices. Double-click the device
1.
icon to open the device configuration.
Configure the virtual router for PIM-SM:
2.
In the device navigation tree, select Network > Virtual Router.
Double-click the virtual router in which you are configuring a PIM-SM instance. The
General Properties screen appears.
In the virtual router navigation tree, select Dynamic Routing Protocol.
Select the Configure PIM-SM check box. PIM-SM configuration options now appear
in the virtual router navigation tree under Dynamic Routing Protocol.
In the virtual router navigation tree, select Dynamic Routing Protocol > PIM-SM >
Acceptable Groups.
Select the access list that identifies the permitted multicast group(s).
In the Group Specific Access Policies area, click the Add icon to map a multicast
group to access lists. The Multicast Group IP dialog box appears.
Enter the IP address of the multicast group for which you created access lists for
permitted RPs and permitted sources.
Select the ID of the access list that identifies the permitted RP(s). The device drops
traffic for the multicast group if the traffic is from an RP that is not on the access
list.
Select the ID of the access list that identifies the permitted source(s). This prevents
unauthorized sources from sending data into your network. When you use this
feature, the device drops multicast data from sources not in the list.
Click OK to save the new Multicast Group IP.
3.
Click OK to save your changes to the virtual router, and then click OK again to save
4.
your changes to the device configuration.
Access List Overview on page 298
RIP Overview on page 321
Multicast Route Overview on page 337
Configuring a Rendezvous Point to Group Mappings (NSM Procedure) on page 342
Example: Configuring Proxy RP on page 345
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5