Disabling Irdp - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Related
Documentation
Disabling IRDP
350
Table 85: IRDP Protocol Settings
IRDP Parameters
IPv4 address
Broadcast Advertisement
Init Advertise Interval after
Enable
Init Advertise Packet Count
Lifetime
Max Advertise Interval
Min Advertise Interval
Response Delay
Multicast Route Overview on page 337
Multicast Routing Table Entries Overview on page 346
Multicast Routing Table Preferences Overview on page 346
IRDP Support Overview on page 348
Disabling IRDP on page 350
Example: Configuring Multicast Static Routes (NSM Procedure) on page 347
You can disable an interface from running IRDP; however, when you do so, ScreenOS
deletes all related memory from the original configuration.
To disable the Trust interface from running IRDP, enter the following command:
unset interface trust protocol irdp enable
NOTE: For details on viewing IRDP information from the Web UI or the CLI,
see the Concepts & Examples ScreenOS Reference Guide.
Default Values
Primary and secondary IP
addresses—advertised
Management and webauth
IP addresses—not advertised
Disabled
16 seconds
3
Three times the Max Advertise
Interval value
600 seconds
75% of the Max Advertise
Interval value
2 seconds
Available Settings
Advertise—you can add a
preference value (-1through
2147483647)
Enabled
1 through 32 seconds
1 through 5
Max Advertise Interval value
through 9000 seconds
4 through 1800 seconds
3 through Max Advertise Interval
value
0 through 4 seconds
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?