Configuring Multicast Static Routes; Example: Configuring Multicast Static Routes (Nsm Procedure) - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Related
Documentation
Configuring Multicast Static Routes
Related
Documentation
Example: Configuring Multicast Static Routes (NSM Procedure)
Copyright © 2010, Juniper Networks, Inc.
Multicast Route Overview on page 337
Multicast Routing Table Entries Overview on page 346
Configuring Multicast Static Routes on page 347
For each static entry in the multicast routing table, you must configure the following
information:
Multicast Group IP—Enter the IP address of the group that receives multicast traffic.
Source IP—Enter the IP address of the source of the multicast traffic.
Incoming Interface—Select the interface on the device that receives multicast traffic.
Outgoing Information—Enter the information that defines the interface and IP address
the device uses to forward multicast traffic.
Outgoing Interface—Select the interface on the device that forwards multicast traffic.
Outgoing Group—Security devices can translate the original multicast group address
to a different multicast group address on the outgoing interface. Use this option to
specify the translated multicast group address for the outgoing interface (you
configure the original group address in the Multicast Group IP setting).
Multicast Route Overview on page 337
Multicast Routing Table Entries Overview on page 346
Multicast Routing Table Preferences Overview on page 346
Configuring IGMP (NSM Procedure) on page 338
Configuring IGMP Proxy (NSM Procedure) on page 339
Example: Configuring Multicast Static Routes (NSM Procedure) on page 347
You can configure multiple Outgoing Information settings for a single static multicast
route.
In this example, you configure a static multicast route from a source with IP address
20.20.20.200 to the multicast group 238.1.1.1. You configure the security device to translate
the multicast group from 238.1.1.1 to 238.2.2.1 on the outgoing interface.
Chapter 10: Routing
347
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?