Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual page 335
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
Figure 5: Source Interface-Based Routing Overview
To configure source interface-based routing:
Add a NetScreen-5400 device running ScreenOS 5.x, and then configure the network
1.
module:
In the NSM navigation tree, select Device Manager > Devices. Double-click the
device object to open the device configuration.
Double-click the device icon to open the device configuration. In the device navigation
tree, select Network > Slot.
Double-click slot 2 to display the slot configuration dialog box. For Card Type, select
5000-8G SPM.
Click OK to save the slot configuration, and then click Apply to apply the new
interfaces to the device.
Configure the ethernet 2/1 and ethernet 2/3 interfaces. In the device navigation tree,
2.
select Network > Interface.
Double-click the ethernet2/1 interface. The General Properties screen appears.
3.
Configure the following options:
For Zone, select Trust.
For IP address and Netmask, enter 10.1.1.0/24.
Click OK to save your changes to the interface.
Double-click the ethernet2/3 interface. The General Properties screen appears.
4.
Configure the following options:
For Zone, select Trust.
For IP address and Netmask, enter 10.1.2.0/24.
Click OK to save your changes to the interface.
In the device navigation tree, select Network > Virtual Routers. Double-click the
5.
trust-vr virtual router. The General Properties screen appears. In the router navigation
tree, select Routing Table.
Select Enable Source-Based Routing.
6.
Chapter 10: Routing
311
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?
Questions and answers