Synchronizing Virtual Router Configurations; Configuring The Virtual Router Synchronization Settings - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 Manual
Configuring screenos devices guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01:
- Manual (340 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Configuring ScreenOS Devices Guide
Synchronizing Virtual Router Configurations
Configuring the Virtual Router Synchronization Settings
372
After you add new members to an NSRP cluster, you must synchronize the configuration
and files from one device to another.
To synchronize configurations:
In the NSM navigation tree, select Device Manager > Devices, and then double-click
1.
the cluster to open the cluster configuration.
In the Device Manager, double-click the cluster to open the cluster configuration.
2.
In the cluster navigation tree, select NSRP Directives > Flash Sync.
3.
Select the device that will be used to synchronize the other device and click Perform
4.
Sync. The device that has been synchronized is automatically rebooted to activate
the new configuration.
Click OK to save your changes to the cluster.
5.
You can configure the virtual router information for the cluster or cluster members. For
devices running 5.0, you must configure the virtual router settings at the system level
(the cluster).
For devices running ScreenOS 5.1 and later, you can configure the virtual router setting
at the system level (the cluster) or at the local level (cluster member). By default, cluster
members automatically use the virtual router settings of the cluster. To use different
vrouter settings for each cluster member, you must disable NSRP configuration
synchronization for the vrouter at the system level:
In the NSM navigation tree, select Device Manager > Devices, and then double-click
1.
the cluster to open the cluster configuration.
In the cluster navigation tree, select Network > Virtual Router. Double-click the trust-vr
2.
virtual router. The General Properties screen appears.
Clear the Enable NSRP Configuration Sync for Vrouter check box, and then click
3.
Apply to save your changes to the cluster.
In the cluster navigation tree, select Members and double-click a cluster member
4.
device to open the device configuration. Edit the virtual router settings as desired.
NOTE: The Enable NSRP Configuration Sync setting does not affect the
virtual router ID. The virtual router ID setting is always configured at the
local level (cluster member).
Click OK to save your changes to the cluster member, and then click OK to save your
5.
changes to the cluster.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING SCREENOS DEVICES GUIDE REV 01 and is the answer not in the manual?
Questions and answers