Juniper JUNOS OS 10.4 - FOR EX REV 1 Manual page 243

Additional Information
Required Privilege
Level
List of Sample Output
show system show system
boot-messages (TX boot-messages (TX
Matrix Router) Matrix Router)
Copyright © 2010, Juniper Networks, Inc.
—(TX Matrix Plus routers only) (Optional) Display boot time messages for the
sfc number
TX Matrix Plus router (or switch-fabric chassis). Replace number with
By default, when you issue the
or TX Matrix Plus master Routing Engine, the command is broadcast to all the T640 (in
a routing matrix based on a TX Matrix router) master Routing Engines or T1600 (in a
routing matrix based on a TX Matrix Plus router) master Routing Engines connected to
it. Likewise, if you issue the same command on the TX Matrix or TX Matrix Plus backup
Routing Engine, the command is broadcast to all the T640 (in a routing matrix based on
a TX Matrix router) backup Routing Engines or T1600 (routing matrix based on a TX
Matrix Plus router) backup Routing Engines that are connected to it.
view
show system boot-messages (TX Matrix Router) on page 139
show system boot-messages lcc (TX Matrix Router) on page 140
show system boot-messages (TX Matrix Plus Router) on page 141
user@host> show system boot-messages
Copyright (c) 1992-1998 FreeBSD Inc.
Copyright (c) 1996-2000 Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California.
JUNOS 4.1-20000216-Zf8469 #0: 2000-02-16 12:57:28 UTC
tlim@single.juniper.net:/p/build/20000216-0905/4.1/release_kernel/sys/compil
e/GENERIC
CPU: Pentium Pro (332.55-MHz 686-class CPU)
Origin = "GenuineIntel"
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,<b
16>,<b17>,MMX,<b24>>
Teknor CPU Card Recognized
real memory = 805306368 (786432K bytes)
avail memory = 786280448 (767852K bytes)
Probing for devices on PCI bus 0:
chip0 <generic PCI bridge (vendor=8086 device=7192 subclass=0)> rev 3 class 6000
0 on pci0:0:0
chip1 <Intel 82371AB PCI-ISA bridge> rev 1 class 60100 on pci0:7:0
chip2 <Intel 82371AB IDE interface> rev 1 class 10180 on pci0:7:1
chip3 <Intel 82371AB USB interface> rev 1 class c0300 int d irq 11 on pci0:7:2
smb0 <Intel 82371AB SMB controller> rev 1 class 68000 on pci0:7:3
pcic0 <TI PCI-1131 PCI-CardBus Bridge> rev 1 class 60700 int a irq 15 on pci0:13
:0
TI1131 PCI Config Reg: [pci only][FUNC0 pci int]
pcic1 <TI PCI-1131 PCI-CardBus Bridge> rev 1 class 60700 int b irq 12 on pci0:13
:1
TI1131 PCI Config Reg: [pci only][FUNC1 pci int]
fxp0 <Intel EtherExpress Pro 10/100B Ethernet> rev 8 class 20000 int a irq 12 on
pci0:16:0
chip4 <generic PCI bridge (vendor=1011 device=0022 subclass=4)> rev 4 class 6040
0 on pci0:17:0
fxp1 <Intel EtherExpress Pro 10/100B Ethernet> rev 8 class 20000 int a irq 10 on
pci0:19:0
Chapter 10: Operational Commands for Software Installation
show system boot-messages
Id = 0x66a Stepping=10
.
0
command on a TX Matrix
All rights reserved.
139