Xerox Telecopier 7033 Service Manual page 282

16. Connect AC power to the terminal and the external power supply
(Ethernet thick cable type only).
17. Enter the service mode and perform a diagnostic self test on the
terminal.
System Check
Note: The network connection is not yet made. The LED sequence on
the Fax Server PWB will not end with the normal indications.
1. Power on the terminal and external power supply (if connected). If
the normal idle display appears continue with step 2. If not go to
System Check procedures in Section 1 of this manual.
2. The Red and Green LEDs on the Fax Server PWB will blink on and off
once. Then the Green LED will flash from dim to bright for about 3
seconds then blink on and off for about 5 seconds. Then the led's
will remain off. At the end of the LED sequence a diagnostic print
out (Refer to figures 3 & 4) will be printed on the terminal or
optional printer if installed.
Fax Server PWB ID number and a fault that relates to the Fax Server
not being connected to the network.
occur proceed to the Repair Analysis Procedures in this section.
7033 LAN Fax Server Ethernet PWB ID Number
# 04200011 - 10BASE2 [thin]
****** 7033 Lan Fax Server - Token Ring 0.15 build date Apr 15. 1992 10:36:03 AM
Failed configuration of 7033 LAN Fax Server - Ethernet : 04200011 (#1)
Network: 00 00 00 05 #1 #2 30 34 32 30 30 31 31
Default server : FS1
7033 Lan Fax Server - Token Ring Diagnostics
------------------------
Token - Ring IBM - Source - Routing Mode
MAC layer packet size + 4352
KNOWN FILE SERVERS
---------------------------
[X1] FS1 V2.15 (ID 0X14a0045) [00 00 00 05 ]
[Xffffffff] FS3
[Xffffffffl FS2
Figure 3 Ethernet Thin Example
1.5.1
The diagnostic print contains the LAN
If this sequence does not
www.printcopy.info
7033 LAN Fax Server Ethernet PWB ID Number
# 04200011 - [thick]
****** 7033 Lan Fax Server - Ethernet 0.12 build date Apr 08. 1992 01:54:03 PM
Failed configuration of 7033 LAN Fax Server - Ethernet: 04200011 (#1)
Network: 00 00 00 05 #1 #2 30 34 32 30 30 30 31 32
Default server: FS1
7033 LAN Fax server - Ethernet Diagnostics
----------------------
Ethernet IEEE 802.3 10x 01
MAC layer packet size =1152
KNOWN FILE SERVERS
----------------------
[X1] FS1 V2.15 (ID 0X f500b3) [00 00 00 05 ]
[Xffffffff] FS3
[Xffffffffl FS2
Figure 4 Ethernet Thick Example
3. Print an Options Report. Observe that the report shows two options
installed, the RS-232 and LAN Fax Server. The report indicates an
RS232 option is installed when in fact no option exist.
because some of the data buss signals are common between both
options and are recognized by the terminal.
RS232 option listed on the report should be ignored.
however confirm that the terminal has recognized the "LAN Fax
Server " in the Option Name column and "Ethernet" in the Status
column.
4. Remove power from the terminal and the external power supply (if
connected). At this point if the Network software has been loaded,
the Ethernet connection can be applied. If an optional printer is to
be used that connection may also be applied. It is recommended
that the network supervisor make these connections and perform
all required setup procedures for their network. The setup
procedures are located in the Supervisors Handbook.
6/92
8h-18
All references to the
You should
Telecopier 7032 / 7033 Service Manual
This is