Fuji Xerox DocuPrint CM305 df Service Manual page 700

Chain
Description
-Link
825-050 SiDAA Operation Mode
825-054 OFF HOOK Threshold selection ONHOOK_LVS_THRESH_HI
825-060 DM Prevention function
825-062 Dial Pulse Quantity
825-063 PB Sending Time
825-064 PB Pause Time
DTMF Sending Attenuation
825-065
Level
DTMF difference between high-
825-066
pass and low-pass levels
825-067 10PPS Make Time
825-068 10PPS Break Time
825-069 20PPS Make Time
825-070 20PPS Break Time
825-071 DP Interdigit Pause Time
825-072 (4/0.1) Pause Time
825-073 Blind Dial Time
Time to time out Dial Tone
825-074
Detection
825-079 ONHOOK Detection Time
OFF HOOK detection time with
825-080 RING Signal not existing on the
line.
OFF HOOK detection time with
825-081
RING Signal existing on the line
825-083 Ring Volume setting
Name
DAA_MODE
UNWANTED_REMOTE_PREVENTI
ON
NUM_DIAL_PULSE
PB_TONE_TIME
PB_INTERDIGIT
PB_ATT_LEVEL
PB_LEVEL_SUB
MAKE_10PPS
BREAK_10PPS
MAKE_20PPS
BREAK_20PPS
DP_INTERDIGIT
PAUSE_TIME
BLIND_TIME
TIME_TO_DETECT_DIALTONE
ONHOOK_DETECT_TIME
OFFHOOK_DETECT_TIME
OFFHOOK_DETECT_TIME_RING
RINGER_VOLUME
Value Label Default
0x00 ～ 0xFF
0x01: Reserve
0x02: Reserve
0x04: Check RING with
Line Monitor ON
0x00
0x08: Reserve
0x10: Reserve
0x20: Reserve
0x40: Reserve
0x80: Reserve
0:Low
1:Medium 1
2:High
0: Prohibit
0
1: Permit
0:N
1:10-N 0
2:N+1
0 ～ 255:0ms ～ 255ms
100
1ms/step
0 ～ 255:0ms ～ 255ms
120
1ms/step
4 ～ 15:-4dbm ～ -15dBm 6
0:2.0dB
1:2.5dB
2:3.0dB
3:3.5dB
4:4.0dB
5:4.5dB 0
6:5.0dB
12:0dB
13:0.5dB
14:1.0dB
15:1.5dB
1 ～ 106:1ms ～ 106ms
31
1ms/step
1 ～ 106:1ms ～ 106ms
67
1ms/step
1 ～ 106:1ms ～ 106ms
16
1ms/step
1 ～ 106:1ms ～ 106ms
34
1ms/step
0 ～ 255:0ms ～ 5110ms
36
20ms/step
0 ～ 255:0ms ～ 25500ms
40
100ms/step
3 ～ 255:3s ～ 255s
-- The setting range below
applies to South Africa
3
only.
1 ～ 255：1s ～ 255s
0 ～ 255:0s ～ 255s
20
1S/step
10 ～ 255:200ms ～
65
5100ms
20ms/step
15 ～ 255s:300ms ～
15
5100ms
20ms/step
15 ～ 255ms 300ms ～
15
5100ms
20ms/step
0: Mute
1: low
3
2: medium
3: high
6 – 54
Chapter 6 General
Details Access
"OR" of each bit enables the use
of system data set by nation.
0x01：Reserve
0x02：Reserve
0x04：Decide to detect RING
when Line Monitor is ON.
CE
0x08：Reserve
0x10：Reserve
0x20：Reserve
0x40：Reserve
0x80：Reserve
Selection of External Tel Hook
USER
Status Detection Threshold
USER
DP Pulse Qty selection CE
PB (DTMF) Signal sending time CE
PB minimum pause time CE
DTMF Sending Level setting CE
Set a level difference between
high-pass and low-pass
frequencies in PB (DTMF)
CE
dialing.
Level difference： high-pass to
low-pass
CE
CE
CE
CE
CE
Pause Time. When pause "-" is
pressed, allow this system-data-
CE
specified time before dialing the
next dial data.
With PBX connected, time from
when the line gets connected to
the start of dialing
CE
(An increase of approx. 1.3 sec
from a setting value due to
modem restrictions）
Used as timeout when Dial Tone
CE
cannot be detected.
Time before deciding External
Tel is on hook when it is put on CE
hook.
Time before deciding External
Tel is off hook when it is taken
CE
off hook with RING Signal not
having come.
Time before deciding External
Tel is off hook when it is taken
CE
off hook with RING Signal
coming.
USER
OFF/
ON


