Fuji Xerox DocuPrint CM305 df Service Manual page 144

Step
Checking the Tray 2 Feed Solenoid (SOLENOID FEED
MSI) for operation.
Does the Tray 2 Feed Solenoid (SOLENOID FEED MSI)
operate properly?
11
Checked by [Digital Output] - [Tray 2 Feed Solenoid] in [IOT
Diag] of diagnosis.
During this check, cheat the interlock switch (HARN ASSY
INTERLOCK AIO).
Checking the Tray 2 Turn Clutch (CLUTCH ASSY DRV) for
operation.
Does the Cassette Tray 2 Turn Clutch (CLUTCH ASSY
DRV) operate properly?
12
Checked by [Digital Output] - [Tray 2 Turn Clutch] in [IOT
Diag] of diagnosis.
During this check, cheat the interlock switch (HARN ASSY
INTERLOCK AIO).
Checking the paper lead edge staying position.
13 Does the paper lead edge stay before the ROLL ASSY
REGI and ROLL REGI METAL?
Checking the paper path.
Remove the Tray 1 and Tray 2 paper cassettes.
14
Are there any obstacles on the paper transfer path between
the Tray 2 and the Regi Assy?
Checking the connectors of the SENSOR PHOTO (Paper
Path Sensor) for connection.
15 Check the connections between the PWBA FFE D and
SENSOR PHOTO.
Are P/J420 and P/J4200 connected correctly?
Checking the HARNESS ASSY TRAY COMP for continuity.
Disconnect J420 from the PWB ASSY FEED MG AIO.
16
Disconnect J4200 from the SENSOR PHOTO.
Is each cable of J420 <=> J4200 continuous?
Checking the power to the SENSOR PHOTO.
Disconnect J420 from the PWB ASSY FEED MG AIO.
17
Is the voltage across P420-6pin <=> ground on the PWB
ASSY FEED MG AIO, about +3.3 VDC?
Checking the SENSOR PHOTO for operation.
Check the voltage across J420-5pin <=> ground on the
18 PWB ASSY FEED MG AIO.
Does the voltage change, when the actuator (ACTUATOR
REGI IN) is operated?
Checking the connectors for connection.
Check the connections between the PWB ASSY FEED MG
19
AIO and MOTOR ASSY SUB.
Are P/J422 and P/J4221 connected correctly?
Checking the HARNESS ASSY TRAY MOT for continuity.
Disconnect J422 from the PWB ASSY FEED MG AIO.
20
Disconnect J4221 from the MOTOR ASSY SUB.
Is each cable of J422 <=> J4221 continuous?
Check
2 - 110
Chapter 2 Troubleshooting
Remedy
Yes
Replace the
CASSETTE ASSY Go to step 22.
250 OPT MG AIO.
Go to step 13. Go to step 26.
Replace the KIT
FEEDER ASSY
Go to step 14.
OPT. (Refer to
REP11.1.)
Remove the Replace the KIT
obstacles or stains FEEDER ASSY
from the paper OPT. (Refer to
transfer path. REP11.1.)
Reconnect the
connector(s) P/
Go to step 16.
J420 and/or P/
J4200 correctly.
Replace the
Go to step 17. HARNESS ASSY
TRAY COMP
Replace the PWB
Go to step 18. ASSY FEED MG
AIO.
Replace the
Replace the PWB
SENSOR PHOTO
ASSY FEED MG
(Paper Path
AIO.
Sensor).
Reconnect the
connector(s) P/
Go to step 20.
J422 and/or P/
J4221 correctly.
Replace the
Go to step 21. HARNESS ASSY
TRAY MOT.
No