Kintex-7 Fpga - Xilinx KC705 User Manual

Table 1-1: KC705 Board Component Descriptions (Cont'd)
Reference
Callout
Designator
17 J6, U12 USB-to-UART Bridge
18 P6, U65 HDMI Video Output
19 J31 LCD Character Display
20 U49 I2C Bus Switch, page 47
21 DS11 - DS13 Ethernet PHY Status LEDs
34 DS14, DS20 - DS24 Status LEDs
22 DS1 - DS4, Ds10, User GPIO LEDs
DS25 - DS27
23 SW2 – SW6 User Pushbuttons
24 SW11 GPIO DIP Switch
25 SW8 Rotary Switch
26 J13, J14 GPIO SMA Connectors
27 SW15 Power On/Off Slide Switch SW15
28 SW14 FPGA_PROG_B Pushbutton SW14 (Active-Low)
29 SW13 Configuration Mode and Upper Linear Flash
Address Switch (SW13)
30 J22 HPC Connector J22
31 J2 LPC Connector J2
32 U55, U21, U103, U17, Power Management
U56, U104, U105, U89, side of board, controllers back side of board)
U106, U99, U71, U62,
U17, U18, U33
33 J46 XADC Header
34 J60
35 J39 2 x 5 shrouded PMBus connector
36 J49 12V power input 2 x 3 connector
37 SW7 CPU Reset Pushbutton
Note:

Kintex-7 FPGA

[Figure
The KC705 board is populated with the Kintex-7 XC7K325T-2FFG900C FPGA.
For further information on Kintex-7 FPGAs, see 7 Series FPGAs Overview (DS180)
FPGA Configuration
The KC705 board supports three of the five 7 series FPGA configuration modes:
•
•
•
KC705 Evaluation Board
UG810 (v1.6.2) August 26, 2015
Component Description
(voltage regulators front
2 x 7 2 mm shrouded JTAG cable connector
Jumper header locations are identified in
1-2, callout 1]
Master SPI flash memory using the onboard Quad SPI flash memory
Master BPI flash memory using the onboard Linear BPI flash memory
JTAG using a standard-A to micro-B USB cable for connecting the host PC to the
KC705 board configuration port
www.xilinx.com
Notes
Silicon Labs CP2103GM bridge (back side of board)
and min-B receptacle (front side of board)
Molex 500254-1927, Analog Devices
ADV7511KSTZ-P
2 x 7 0.1 in male pin header
TI PCA9548ARGER
EPHY status LED, dual green
Status LEDs, green
GPIO LEDs, green
E-Switch TL3301EP100QG
C and K 4-pole, SDA05H1SBD
Panasonic EVQ-WK4001
Rosenberger 32K10K-400L5
C and K 1201M2S3AQE2
E-Switch TL3301EP100QG
5-pole C and K SDA05H1IBD
Samtec ASP_134486_01
Samtec ASP_134603_01
TI UCD9248PFC controllers in conjunction with
various regulators
2X10 0.1" male header
Molex 87832-1420
Assman HW10G-0202
Molex 39-30-1060
E-Switch TL3301EP100QG
Appendix A, Default Switch and Jumper
Feature Descriptions
Schematic 0381397
Page Number
27
34, 33
30
32
25
29
29
29
29
29
23
35
29
27
16-19
20
35-46
31
16
35
35
35
Settings.
[Ref 1].
11
Send Feedback