Smart Logic - Danfoss VLT DriveMotor FCP 106 Programming Manual

Parameter Lists
6.1.9 8-** Comm. and Options
Par. Parameter description
No. #
8-0* General Settings
8-01 Control Site
8-02 Control Source
8-03 Control Timeout Time
8-04 Control Timeout Function
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 Baud Rate
8-33 Parity / Stop Bits
8-35 Minimum Response Delay
8-36 Maximum Response Delay
8-4* FC MC protocol set
8-42 PCD Write Configuration
8-43 PCD Read Configuration
8-5* Digital/Bus
8-50 Coasting Select
8-51 Quick Stop Select
8-52 DC Brake Select
8-53 Start Select
8-54 Reversing Select
8-55 Set-up Select
8-56 Preset Reference Select
8-7* BACnet
8-70 BACnet Device Instance
8-72 MS/TP Max Masters
8-73 MS/TP Max Info Frames
8-74 "I am" Service
8-75 Intialisation Password
8-79 Protocol Firmware version
8-8* FC Port Diagnostics
8-80 Bus Message Count
8-81 Bus Error Count
8-82 Slave Messages Rcvd
8-83 Slave Error Count
8-84 Slave Messages Sent
8-85 Slave Timeout Errors
8-88 Reset FC port Diagnostics
8-9* Bus Feedback
8-94 Bus Feedback 1

6.1.10 13-** Smart Logic

Par. No. # Parameter description
13-0* SLC Settings
13-00 SL Controller Mode
13-01 Start Event
®
VLT DriveMotor FCP 106 and FCM 106 Programming Guide
Default value
[0] Digital and ctrl.word
[1] FC Port
1.0 s
[0] Off
[0] FC
1.0 N/A
ExpressionLimit
ExpressionLimit
0.01 s
ExpressionLimit
ExpressionLimit
ExpressionLimit
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
[0] Digital input
[3] Logic OR
[3] Logic OR
1 N/A
127.0 N/A
1.0 N/A
[0] Send at power-up
[admin]
ExpressionLimit
0.0 N/A
0.0 N/A
0.0 N/A
0.0 N/A
0.0 N/A
0.0 N/A
[0] Do not reset
0.0 N/A
Default value
[0] Off
[39] Start command
MG03N102 - Rev. 2013-12-02
2-set-up Change Conver-
during sion index
operation
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
2-set-up Change
during
operation
1 set-up TRUE
1 set-up TRUE
Type
- Uint8
- Uint8
-1 Uint16
- Uint8
- Uint8
0 Uint8
- Uint8
6
- Uint8
-3 Uint16
-3 Uint16
0 Uint8
0 Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
0 Uint32
0 Uint8
0 Uint16
- Uint8
0 VisStr[21]
-2 Uint16
0 Uint32
0 Uint32
0 Uint32
0 Uint32
0 Uint32
0 Uint32
- Uint8
0 Int16
Conver- Type
sion
index
- Uint8
- Uint8
105
6