Danfoss VLT DriveMotor FCP 106 Programming Manual page 74

Parameters
13-40 Logic Rule Boolean 1
Array [6]
Option:
[1] True
[2] Running
4 4
[3] In range
[4] On reference
[7] Out of current
range
[8] Below I low
[9] Above I high
[16] Thermal
warning
[17] Mains out of
range
[18] Reversing
[19] Warning
[20] Alarm (trip)
[21] Alarm (trip lock) See parameter 13-01 Start Event for further
[22] Comparator 0
[23] Comparator 1
[24] Comparator 2
[25] Comparator 3
[26] Logic rule 0
[27] Logic rule 1
[28] Logic rule 2
[29] Logic rule 3
[30] SL Time-out 0
[31] SL Time-out 1
72
®
VLT DriveMotor FCP 106 and FCM 106 Programming Guide
Function:
Enters the fixed value TRUE in the logic
rule.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
See parameter 13-01 Start Event for further
description.
description.
Use the result of comparator 0 in the
logic rule.
Use the result of comparator 1 in the
logic rule.
Use the result of comparator 2 in the
logic rule.
Use the result of comparator 3 in the
logic rule.
Use the result of logic rule 0 in the logic
rule.
Use the result of logic rule 1 in the logic
rule.
Use the result of logic rule 2 in the logic
rule.
Use the result of logic rule 3 in the logic
rule.
Use the result of timer 0 in the logic rule.
Use the result of timer 1 in the logic rule.
MG03N102 - Rev. 2013-12-02
13-40 Logic Rule Boolean 1
Array [6]
Option: Function:
[32] SL Time-out 2 Use the result of timer 2 in the logic rule.
[33] Digital input Use the value of DI18 in the logic rule
DI18 (High = TRUE).
[34] Digital input Use the value of DI19 in the logic rule
DI19 (High = TRUE).
[35] Digital input Use the value of DI27 in the logic rule
DI27 (High = TRUE).
[36] Digital input Use the value of DI29 in the logic rule
DI29 (High = TRUE).
[39] Start command This logic rule is TRUE if the frequency
converter is started by any means (either
via digital input, or other).
[40] Drive stopped This logic rule is TRUE if the frequency
converter is stopped or coasted by any
means (either via digital input, or other).
[42] Auto Reset Trip This logic rule is TRUE if the frequency
converter is tripped (but not trip-locked)
and an Automatic Reset is issued.
[50] Comparator 4 Use the result of comparator 4 in the
logic rule.
[51] Comparator 5 Use the result of comparator 5 in the
logic rule.
[60] Logic rule 4 Use the result of logic rule 4 in the logic
rule.
[61] Logic rule 5 Use the result of logic rule 5 in the logic
rule.
[70] SL Time-out 3 Use the result of timer 3 in the logic rule.
[71] SL Time-out 4 Use the result of timer 4 in the logic rule.
[72] SL Time-out 5 Use the result of timer 5 in the logic rule.
[73] SL Time-out 6 Use the result of timer 6 in the logic rule.
[74] SL Time-out 7 Use the result of timer 7 in the logic rule.
[83] Broken Belt A broken belt condition has been
detected. This function must be enabled
in parameter 22-60 Broken Belt Function.
13-41 Logic Rule Operator 1
Option:
[0] Disabled
*
[1] AND
[2] OR
[3] AND NOT
[4] OR NOT
[5] NOT AND
[6] NOT OR
[7] NOT AND NOT
[8] NOT OR NOT
Function: