Xerox WorkCentre 4150 Service Manual page 314

• Table 15 Output Codes 10
• Table 16 Output Codes 12
• Table 17 Output Codes 20
Procedure
1. Enter Diagnostics, GP 1.
2. Select Diagnostics Routines.
3. Select required dC routine category:
• Copier Routines, 330 Component Control.
• Fax dC Routines, 330 Component Control.
4. Select and input the required codes as follows:
NOTE: To clear an incorrectly entered code and reset the Add Component button to
00.000, press the hard key C.
a. From the component control Input Components tables and the Output Components
tables, select and enter the appropriate code into the Add Component button, and
touch the button. This will add the component to the top of the Component Name
table list. When the list is full, the addition of more components will cause compo-
nents to be deleted from the bottom of the list.
NOTE: Fax component control codes can only be energized one at a time.
b. If a control code is not known, it can be selected from the list displayed when the
Find Component button is touched, as follows:
NOTE: The 'Find Component' button is not available if components are energized.
i. Enter the chain number into the Chain: button and touch the Find Component
button to display the control codes for that chain.
ii. Use the scroll buttons to locate the required code, touch the Component Name
button to highlight it and touch Select.
iii. Repeat as required to add components to the Component Name table.
iv. Touch Save to save the selections to the Component Name table list and return
to the Component Control window.
5. To energize a component or group of components:
a. Touch the control code to highlight it.
b. Touch Start.
c. The status of the component is shown in the Status column i.e.:
i. On
ii. Off
iii. High
iv. Low
v. A numeric value with up to four digits e.g. 0020.
6. Touch a component in the component table and then touch Stop to stop that component.
To stop all components touch Stop All.
7. Touch Exit to close the Component Control window.
8. To exit diagnostics mode, GP 1, select the Call Close Out button.
General Procedures and Information
dC330
Input Codes
Code Displayed Name Description
01-100 Side cover interlock Side cover interlock switch (S01-
100), detects if the side cover is
open.
01-200 Exit cover present Exit cover present sensor (Q01-
sensor 200), detects when the exit cover
is present.
Code Displayed Name Description
04-110 Main BLDC Motor Detects when the BLDC motor
Ready (MOT04-110) is running at required
speed.
04-410 Duplex Fan 1 Run Detects if fan 1 is running at normal
Ready speed.
04-420 Duplex Fan 2 Run Detects if fan 2 is running at normal
Ready speed.
Code Displayed Name Description
05-100 DADF Doc. Detect DADF document detect sensor
Sensor (Q05-100), detects if a document is
present.
05-110 DADF Paper Width DADF document width sensor
Sensor (Q05-110), detects the width of the
document.
05-120 DADF Paper DADF document length sensor
Length Sensor (Q05-120), detects the length of the
document.
05-130 DADF Registration DADF document registration sen-
Sensor sor (Q05-130), detects if a docu-
ment is present.
05-140 DADF Scan Sensor DADF document scan sensor
(Q05-140), detects if a document is
present.
05-150 DADF Gate Sensor DADF document gate sensor (Q05-
150), detects if a document is
present.
September 2006
6-44
Table 1 Input codes 01
General
Closed = side cover closed
Opened = side cover
opened
Closed = exit cover
installed
Opened = exit cover not
installed
Table 2 Input codes 04
General
High = running normal
speed
Low = not running at nor-
mal speed
High = running at normal
speed
Low = not running at nor-
mal speed
High = running at normal
speed
Low = not running at nor-
mal speed
Table 3 Input codes 05
General
High = document present
Low = no document
High = made
High = document present
Low = no document
High = document present
Low = no document
High = document present
Low = no document
High = document present
Low = no document
WorkCentre 4150