Xerox WorkCentre 4150 Service Manual page 310

Table 5 NVM chain 9
Location NVM Name NVM Description
09-100 LD Light Level 600dpi laser light level. Value
in PWM.
09-110 MHV Control Bias Main charge bias control.
Control Basic of value (HVPS setting is
value). Value in PWM.
09-120 THV Bias Control Transfer bias control. Basic of
Control value (HVPS setting is value).
Value in PWM.
09-130 Deve Bias Control DEVE bias control. Basic of
value (HVPS setting is value).
Value in PWM standard volt-
age: --500V (PWM 522).
09-140 Detack Bias Con- Detack bias control. Basic of
trol value (HVPS setting is value).
Value in PWM standard volt-
age: -1800V.
09-200 Drum Life Page Display of drum pages count.
Counter
09-210 Toner Cartridge Display of toner cartridge
Life Page Counter pages count.
09-230 Transfer Roller Display value of pages count.
Life Page Counter
Table 6 NVM chain 10
Location NVM Name NVM Description
10-100 Standby Temper- Target temperature during
ature Offset standby mode.
10-105 Run Temperature Target temperature during run
Offset mode.
10-110 Low Paper Tem- Target temperature during
perature Offset power save mode.
10-115 101-185 mm Offset temperature required on
Temperature Off- thermistor B for paper width.
set
10-120 186-216 mm Offset temperature required on
Temperature Off- thermistor B for paper width.
set
10-125 60gms Tempera- Media type offset for fuser roll
ture Offset temperature.
General Procedures and Information
dC131
Value Default Location NVM Name
200 to 600 350 10-130
108 to 145 126
10-135
41 to 220 76
10-140
408 to 607 522
10-145
80 to 160 123 10-150
10-155
(Read only)
(Read only) 10-200
(Read only) 10-210
10-220
10-300
Value Default
0 to 15 (4 steps/ 10
10-310
5 degrees inter-
val)
0 to 10 (3 steps/ 5
5 degree inter-
vals)
Location NVM Name
0 to 40 (9 steps/ 20
5 degree inter-
20-100
vals)
0 to 15 (4 steps/ 5
20-110
5 degree inter-
vals)
20-200
0 to 15 (4 steps/ 5
20-210
5 degree inter-
vals)
20-220
0 to 15 (4 steps/ 5
5 degree inter-
20-300
vals)
20-310
September 2006
6-40
Table 6 NVM chain 10
NVM Description
90gms Tempera- Media type offset for fuser roll
ture Offset temperature.
Bond Tempera- Media type offset for fuser roll
ture Offset temperature.
Transparency Media type offset for fuser roll
Temperature Off- temperature.
set
Cardstock Tem- Media type offset for fuser roll
perature Offset temperature.
Envelopes Tem- Media type offset for fuser roll
perature Offset temperature.
Labels Tempera- Media type offset for fuser roll
ture Offset temperature.
Fuser Life Page (Read only)
Counter
Heat Roll Life (Read only)
Page Counter
Pressure Roll Life (Read only)
Page Counter
Pick-up Interval Change the time interval for
Delay paper pick-up.
Pick-up Interval Change the time interval for
Delay (Special paper pick-up.
Paper)
Table 7 NVM chain 20
NVM Description
Redial Attempts Number of times to
redial.
Redial interval Time between each
redial.
Pause Dial Time Time of each pause.
Dial Pulse M/B Dial pulse make/break
Ratio ratio.
Auto Dial Start Pause time before auto-
Pause Time dialing (second)
Ring On Time Ring on time.
Ring Off Time Ring off time.
Value Default
0 to 10 (3 steps/ 5
5 degree inter-
vals)
0 to 10 (3 steps/ 5
5 degree inter-
vals)
0 to 10 (3 steps/ 5
5 degree inter-
vals)
0 to 10 (3 steps/ 5
5 degree inter-
vals)
0 to 10 (3 steps/ 5
5 degree inter-
vals)
0 to 10 (3 steps/ 5
5 degree inter-
vals)
0 to 100 msec. 0
0 to 100 msec. 0
Value Default
1 to 13 7
1 to 15 3
0 to 200 (1000 msec.) 4
33/66 (0) or 40/60 (1) 1
0 to 10 seconds 1
0 to 99msec. 80
0 to 99 msec. 80
WorkCentre 4150