Page 1 ZXA10 C300 Optical Access Convergence Equipment Configuration Manual (CLI) Version: V2.0.0 ZTE CORPORATION No. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057 Tel: +86-755-26771900 Fax: +86-755-26770801 URL: http://support.zte.com.cn E-mail: support@zte.com.cn...
Page 2 ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations. All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE CORPORATION or of their respective owners.
Page 3: Table Of Contents
1.5.4 Disconnecting an Online User ..............1-23 Chapter 2 GPON/XG-PON Service Configuration........2-1 2.1 Configuring the GPON ONU Type Profile ............. 2-3 2.2 Authenticating the GPON ONU ................2-4 2.3 Configuring the T-CONT Bandwidth Profile ............2-6 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 4 7.1.6 Configuring Traffic Shaping ............... 7-5 7.1.7 Configuring the Mapping Relation From CoS to Local Queues ....7-6 7.2 OLT Interface QoS Configuration................. 7-6 7.2.1 Configuring Queue Scheduling..............7-6 7.2.2 Configuring Queue Mapping ..............7-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 5 12.3 Configuring CTLA 1+1 Protection ..............12-6 Chapter 13 PON Protection Configuration..........13-1 13.1 Configuring PON Port Protection ..............13-1 Chapter 14 Access Security Configuration..........14-1 14.1 Port Identification Configuration............... 14-1 14.1.1 Configuring the Port Identification ............14-1 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 6 16.4.1 Configuring the Basic PWE3 Service ............16-54 16.4.2 Configuring Multi-Segment PWs ............16-61 16.4.3 Configuring the TDM Relay Service ............16-68 16.5 PW Redundancy Configuration...............16-78 16.5.1 Configuring the VPLS Redundancy............16-78 16.5.2 Configuring the VLL Resilience.............16-87 16.5.3 Configuring the PW Redundancy and BFD..........16-96 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 7 19.1 Configuring the Synchronous Ethernet Clock............ 19-1 19.2 Configuring External Input Clock ..............19-3 19.3 Configuring the External Output Clock ............. 19-4 19.4 Configuring PTP Slave Clock ................19-6 Figures......................I Tables ......................III Glossary .......................VII SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 8 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 9: About This Manual
About This Manual Purpose The ZXA10 C300 Optical Access Convergence Equipment (ZXA10 C300 for short) is a full-service optical access platform. It supports the video, data, voice, TDM, and CATV services. The ZXA10 C300 can be connected with MDUs/ONUs/ONTs through various networking technologies.
Page 10 Describes OAM configuration. 18, Route Protocol Configuration Describes route protocol configuration 19, Clock Configuration Describes clock configuration. Conventions This manual uses the following typographical conventions: Typeface Meaning Note: provides additional information about a certain topic. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 11: Chapter 1 Basic Configuration
Perform this procedure to log in to the ZXA10 C300 through HyperTerminal. Context When you log in to the ZXA10 C300 through HyperTerminal, the user name and password are case-sensitive. This topic takes the Windows XP operating system as the example.
Page 12: Figure 1-1 Connection Description
ZXA10 C300 Configuration Manual (CLI) Figure 1-1 Connection Description 2. Fill in Name and click OK. The Connect To dialog box is displayed, as shown in Figure 1-2. Figure 1-2 Connect To 3. Select COM1 or COM2, and then click OK. The COM1 Properties (or COM2 Properties) dialog box is displayed.
Page 13: Login Through Telnet
ZXAN>enable Password: ZXAN# – End of Steps – 1.1.2 Login Through Telnet Perform this procedure to log in to the ZXA10 C300 through Telnet. Prerequisite Before this operation, make sure that: The in-band or out-of-band NM IP address is configured.
Page 14: Login Through Nms
ZXA10 C300 Configuration Manual (CLI) Context When you log in to the ZXA10 C300 through Telnet, the user name and password are case-sensitive. Steps 1. In Windows, click Start > Run to display the Run dialog box, as shown in Figure 1-4.
Page 15: Nm Configuration
1.2 NM Configuration The ZXA10 C300 supports in-band NM and out-of-band NM. In in-band NM mode, the ZXA10 C300 accesses the IP network via the service channel (uplink port) to transmit NM information. The in-band NM mode is usually used in practical engineering.
Page 16 ZXA10 C300 Configuration Manual (CLI) Enter configuration commands, one per line. End with CTRL/Z. ZXAN(config)# 2. Add the uplink port to the in-band NM VLAN. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 1000 tag ZXAN(config-if)#exit Note: When you use the switchport vlan command to configure the port VLAN, the system automatically creates the VLAN.
Page 17: Configuring The Out-Of-Band Nm
When the ZXA10 C300 is faulty, the network equipment information can be located in time and monitored in real time. Prerequisite You have logged in to the ZXA10 C300 through HyperTerminal and entered administrator mode. Configuration Data Table 1-2 lists the configuration data of the out-of-band NM.
Page 18: Physical Configuration
ZXAN#write – End of Steps – 1.3 Physical Configuration 1.3.1 Adding a Rack When commissioning the ZXA10 C300, you need to add a rack. Context The ZXA10 C300 supports the following two types of racks: ETSI 21: 21-inch rack IEC 19: 19-inch rack Steps 1.
Page 19: Adding A Shelf
Chapter 1 Basic Configuration ZXAN(config)# 2. Add the rack. ZXAN(config)#add-rack rackno 1 racktype ETSI21 Note: The ZXA10 C300 supports only one rack currently, and thus rackno can only be 1. 3. (Optional) Query the rack configuration. ZXAN(config)#show rack Rack RackType...
Page 20: Adding A Card
ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#add-shelf shelfno 1 shelftype ETSI_SHELF Note: The ZXA10 C300 supports only one shelf currently, and thus shelfno can only be 1. 3. (Optional) Query the shelf configuration. ZXAN(config)#show shelf Rack Shelf ShelfType CleiCode Serial-Number ------------------------------------------------------------------------------...
Page 21: Enabling The Pnp Function
INSERVICE – End of Steps – 1.3.4 Enabling the PnP Function The ZXA10 C300 supports the plug and play (PnP) function of the card. By default, the PnP function of the ZXA10 C300 is enabled. Steps 1. In global configuration mode, enable the PnP function.
Page 22: Showing Cards
1.3.5 Showing Cards The card information includes slot No., card type, number of ports, hardware version, software version, and status. Context Table 1-5 describes the card status of the ZXA10 C300. Table 1-5 Card Status Description Status Description INSERVICE The card is working normally.
Page 23: Deleting A Card
When replacing a card with another card of different type, you need to delete the existing card before adding a new card. Steps 1. Enter global configuration mode. ZXAN#configure terminal Enter configuration commands, one per line. End with CTRL/Z. ZXAN(config)# 2. Delete the card. 1-13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 24: Resetting A Card
ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#del-card slotno 15 Confirm to delete card? [yes/no]:y 3. (Optional) Query the card configuration. ZXAN(config)#show card Rack Shelf Slot CfgType RealType Port HardVer SoftVer Status ----------------------------------------------------------------------------- PRWG PRWG INSERVICE PRWG PRWG INSERVICE SCXN SCXN 120900 V2.0.0...
Page 25: Configuring Fans
High-temperature threshold When the ambient temperature is higher than the high-temperature threshold, the ZXA10 C300 reports a high-temperature alarm and disables the interface card. When the ambient temperature is lower than the high-temperature threshold, the ZXA10 C300 enables the interface card again.
Page 26: System Configuration
ZXA10 C300 Configuration Manual (CLI) Note: The ZXA10 C300 supports four temperature levels. You can use the fan control fixed-speed command to set fixed-speed working mode, and then use the fan speed command to set the fan speed level. 2. Configure the speed percent of each level.
Page 27: Configuring The Version Auto-Update Function
Chapter 1 Basic Configuration Context The ZXA10 C300 software maintains the system time. When the NE is powered on, the system acquires the hardware clock and initializes the system time of the NE. Steps 1. In global configuration mode, configure the time zone.
Page 28: Configuring The Auto-Backup Function
--------------------------- enable enable – End of Steps – 1.4.3 Configuring the Auto-Backup Function The ZXA10 C300 supports conditional auto-backup for configuration file, log file, and version files. Configuration Data Table 1-7 lists the configuration data of auto-backup function. Table 1-7 Configuration Data of Auto-Backup Function...
Page 29 1. In global configuration mode, configure the backup file server. ZXAN(config)#file-server auto-backup all server-index 1 ftp ipaddress 10.1.1.1 path bak user zte password zte 2. Configure the condition and interval of the version auto-backup check point. ZXAN(config)#auto-backup condition cfg-changed hold-off-time 1 max-hold-off-time 2 3.
Page 30: Configuring The Auto-Save Function
– End of Steps – 1.5 User Management Users (operators) refer to the personnel who manage and maintain the ZXA10 C300 after logging in to it through CLI terminals, including console port, telnet, or security shell (SSH). The user management defines 16 privilege levels (0 – 15).
Page 31: Adding A User
Maximum session number, 1 – 16 Privilege 0 – 15 The ZXA10 C300 supports maximum 20 users. The default user on the ZXA10 C300 is zte, whose password is ZTEzte123, and the privilege is 1. Steps 1. Add a user.
Page 32: Modifying A User
ZXA10 C300 Configuration Manual (CLI) ----------------------------------------------------------------------- Normal 00:00:00 23:59:59 2099-12-31 23:59:59 admin Normal 00:00:00 23:59:59 2099-12-31 23:59:59 Normal 00:00:00 23:59:59 2099-12-31 23:59:59 Normal 00:00:00 23:59:59 2099-12-31 23:59:59 – End of Steps – 1.5.2 Modifying a User It is recommended to modify user password and privilege in time to ensure the security.
Page 33: Disconnecting An Online User
3. Disconnect the online user. Disconnect the online user by teletypewriter (TTY) line. ZXAN#clear tcp line 69 Disconnect the online user by IP address. ZXAN#clear tcp connect 10.63.192.225 23 10.63.192.213 3641 – End of Steps – 1-23 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 34 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 1-24 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 35: Chapter 2 Gpon/Xg-Pon Service Configuration
The principles of the GPON service and XG-PON service are the same except the downstream bandwidth. GPON service: 2.488 Gbps XG-PON service: 9.553 Gbps Figure 2-1 shows the GPON/XG-PON service networking diagram. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 36: Figure 2-1 Gpon/Xg-Pon Service Networking Diagram
ZXA10 C300 Configuration Manual (CLI) Figure 2-1 GPON/XG-PON Service Networking Diagram Table of Contents Configuring the GPON ONU Type Profile ..............2-3 Authenticating the GPON ONU ..................2-4 Configuring the T-CONT Bandwidth Profile..............2-6 Configuring the GPON ONU IP Profile................2-9 Configuring the GPON ONU VLAN Profile..............2-9 Configuring the VoIP Access Code Profile ..............2-10...
Page 37: Configuring The Gpon Onu Type Profile
ZTE-F641 The ZXA10 C300 supports the only one type of XG-PON ONU: ZTE-F220. On the ZXA10 C300, ZTE-9806, ZTE-F822, and ZTE-F820 are EPON ONU types. If you need to configure the corresponding GPON ONU type, you can use ZTEG-9806H, ZTEG-F822, and ZTEG-F820 respectively.
Page 38: Authenticating The Gpon Onu
Before configuring its services, you need to authenticate the GPON ONU that is online initially. Prerequisite The GPON ONU type profile has been configured by default or manually. Context The ZXA10 C300 supports the following ONU authentication modes: SN authentication SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 39: Table 2-2 Configuration Data For Gpon Onu Authentication
The OLT does not find the ONU because the ONU is offline. logging The OLT has found the ONU and is measuring the distance. syncMib The OLT has measured the distance to the ONU and is synchronizing data. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 40: Configuring The T-Cont Bandwidth Profile
The T-CONT bandwidth profile describes the T-CONT flow parameters. By specifying the T-CONT bandwidth profile, you can implement the T-CONT flow control. Context The ZXA10 C300 supports 512 transmission container (T-CONT) profiles. There are the following five types of upstream bandwidths: Fixed bandwidth (FBW)
Page 41: Table 2-4 Parameters Of The Default T-Cont Profile
T-CONT bandwidth profile 3 Profile name: 10M Bandwidth type: type 3 Assured bandwidth: 5000 kbps Maximum bandwidth: 10000 kbps T-CONT bandwidth profile 4 Profile name: 5M Bandwidth type: type 2 Assured bandwidth: 5000 kbps SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 42 ZXA10 C300 Configuration Manual (CLI) Item Data T-CONT bandwidth profile 5 Profile name: 2M Bandwidth type: type 1 Fixed bandwidth: 2000 kbps Steps 1. In GPON configuration mode, create a T-CONT bandwidth profile. ZXAN(config)#gpon ZXAN(config-gpon)#profile tcont 20M type 5 fixed 2000 assured 5000 maximum 20000...
Page 43: Configuring The Gpon Onu Ip Profile
2.4 Configuring the GPON ONU IP Profile Using the GPON ONU IP profile, you can configure IP addresses for GPON ONUs in batches. Context The ZXA10 C300 supports the following three address allocation modes: Static allocation mode Dynamic Host Configuration Protocol (DHCP) mode Point to Point Protocol over Ethernet (PPPoE) mode One ONU can use only one IP address allocation mode.
Page 44: Configuring The Voip Access Code Profile
ZXA10 C300 Configuration Manual (CLI) Table 2-7 Configuration Data of the GPON VLAN Profile Item Data Profile name vlan-test Tag mode VLAN ID Priority Steps 1. In GPON configuration mode, configure the ONU VLAN profile. ZXAN(config)#gpon ZXAN(config-gpon)#onu profile vlan vlan-test tag-mode tag cvlan 300 pri 7 2.
Page 45: Configuring The Voip Service Application Profile
Steps 1. In GPON configuration mode, configure the VoIP service application profile. ZXAN(config)#gpon ZXAN(config-gpon)#onu profile voip-appsrv voip-service call-waiting enable call-transfer enable call-hold enable 3way enable 2. (Optional) Query the VoIP service application profile. 2-11 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 46 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-gpon)#show gpon onu profile voip-appsrv Profile-name: voip-service calling-num: disable calling-name: disable cid-blocking: disable cid-num-permanent-status: disable cid-name-permanent-status: disable anonymous-cid-blocking: disable call-wating: enable cid-announcement: disable 3way: enable call-transfer: enable call-hold: enable call-park: disable no-disturb: disable emergency-call-flash: disable...
Page 47: Configuring The Dial Plan
Table 2-10 lists the configuration data of the Session Initiation Protocol (SIP) profile. Table 2-10 Configuration Data of the GPON SIP Profile Item Data Profile name sip-test Access code profile Service application profile voip-service 2-13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 48: Configuring The Gpon Mgc Profile
ZXA10 C300 Configuration Manual (CLI) Item Data Dial plan table test IP address of the proxy server 1.2.3.1 Steps 1. In GPON configuration mode, configure the SIP profile. ZXAN(config)#gpon ZXAN(config-gpon)#onu profile sip sip-test proxy 1.2.3.1 ZXAN(config-gpon)#onu profile sip sip-test accesscode abc...
Page 49: Table 2-11 Configuration Data Of The Gpon Mgc Profile
Chapter 2 GPON/XG-PON Service Configuration Context The ZXA10 C300 supports the following two Media Gateway Controller (MGC) protocols. MGCP H.248 Configuration Data Table 2-11 lists the configuration data of the GPON MGC profile. Table 2-11 Configuration Data of the GPON MGC Profile...
Page 50: Configuring The Gpon Broadband Service
ZXA10 C300 Configuration Manual (CLI) Username: Password: Realm: UDP port: 2944 DSCP/TOS: Media UDP port: 2944 Media DSCP/TOS: Message format: text long Version: Maximum retry time: 0(s) Maximum retry attempts: 0(s) Service change delay: 0(s) Softswitch vendor: User TID: Prefix:...
Page 51: Table 2-12 Configuration Data Of The Gpon Broadband Service
User port VLAN Port: eth_0/1 VLAN mode: tag (The untagged upstream packet is tagged with PVID.) VLAN ID: 100 Priority: 0 Configuration Flowchart Figure 2-2 shows the configuration flowchart of the GPON broadband service. 2-17 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 52: Figure 2-2 Configuration Flowchart Of The Gpon Broadband Service
ZXA10 C300 Configuration Manual (CLI) Figure 2-2 Configuration Flowchart of the GPON Broadband Service Steps 1. In ONU interface mode, configure the T-CONT. ZXAN(config)#interface gpon-onu_1/5/1:1 ZXAN(config-if)#tcont 1 name T1 profile 10M 2. Configure the GEM port. ZXAN(config-if)#gemport 1 name gemport1 tcont 1 ZXAN(config-if)#exit 3.
Page 53: Configuring The Gpon Multicast Service
Uplink port gei_1/22/1 Service port ONU interface: gpon-onu_1/5/1:1 Service-port ID: 2 Virtual port ID: 2 T-CONT Index: 2 Name: T2 T-CONT bandwidth profile: 5M GEM Port Index: 2 Name: gemport2 T-CONT index: 2 2-19 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 54 ZXA10 C300 Configuration Manual (CLI) Item Data Service channel Name: mulitcast GEM port index: 2 Priority: 5 VLAN ID: 200 User port VLAN MVLAN ID: 200 MVLAN tag stripping: enable User port VLAN Port: eth_0/2 VLAN mode: tag (The untagged upstream packet is tagged with PVID.)
Page 55: Figure 2-3 Configuration Flowchart Of The Gpon Multicast Service
ZXAN(config-if)#tcont 2 name T2 profile 5M 2. Configure the GEM port. ZXAN(config-if)#gemport 2 name gemport2 tcont 2 ZXAN(config-if)#exit 3. In uplink interface configuration mode, configure the uplink port VLAN. ZXAN(config)#interface gei_1/22/1 ZXAN(config-if)#switchport vlan 200 tag ZXAN(config-if)#exit 2-21 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 56 ZXA10 C300 Configuration Manual (CLI) 4. In ONU interface mode, configure the service port VLAN. ZXAN(config)#interface gpon-onu_1/5/1:1 ZXAN(config-if)#service-port 2 vport 2 user-vlan 200 vlan 200 ZXAN(config-if)#exit Note: By default, the mapping mode between the virtual port and the GEM port is 1:1.
Page 57: Configuring The Gpon Voice Service (Sip)
Service channel Name: voip-sip GEM port index: 3 Priority: 7 VLAN ID: 300 VoIP protocol VoIP address IP address allocation mode: static VoIP IP profile: ip-test IP address: 1.2.3.4/24 VoIP VLAN profile: vlan-test 2-23 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 58: Figure 2-4 Configuration Flowchart Of The Gpon Voice Service
ZXA10 C300 Configuration Manual (CLI) Item Data VoIP service Port: pots_0/1 SIP profile: sip-test User ID: 12345 User name: 12345 Password: 12345 Configuration Flowchart Figure 2-4 shows the configuration flowchart of the GPON voice service. Figure 2-4 Configuration Flowchart of the GPON Voice Service Steps 1.
Page 59: Configuring The Gpon Voice Service (H.248)
VoIP IP profile has been configured. The GPON VoIP VLAN profile has been configured. The GPON profile has been configured. Configuration Data Table 2-15 lists the configuration data of the GPON voice service. 2-25 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 60: Table 2-15 Configuration Data Of The Gpon Voice Service
ZXA10 C300 Configuration Manual (CLI) Table 2-15 Configuration Data of the GPON Voice Service Item Data Service VLAN ID Service priority Uplink port gei_1/22/1 Service port ONU interface: gpon-onu_1/5/1:1 Service-port ID: 3 Virtual port ID: 3 T-CONT Index: 3 Name: voip...
Page 61: Figure 2-5 Configuration Flowchart Of The Gpon Voice Service
3. In uplink interface configuration mode, configure the uplink port VLAN. ZXAN(config)#interface gei_1/22/1 ZXAN(config-if)#switchport vlan 300 tag ZXAN(config-if)#exit 4. In ONU interface configuration mode, configure the service port VLAN. ZXAN(config)#interface gpon-onu_1/5/1:1 ZXAN(config-if)#service-port 3 vport 3 user-vlan 300 vlan 300 ZXAN(config-if)#exit 2-27 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 62 ZXA10 C300 Configuration Manual (CLI) Note: By default, the mapping mode between the virtual port and the GEM port is 1:1. 5. In ONU remote management mode, configure the service channel. ZXAN(config)#pon-onu-mng gpon-onu_1/5/1:1 ZXAN(gpon-onu-mng)#service voip-h248 gemport 3 cos 7 vlan 300 6.
Page 63: Table 3-1 Tdm Interface Cards
The Circuit Emulation Service (CES) provides traditional TDM services based on the Packet Switch Network (PSN), such as E1/T1. The ZXA10 C300 implements the CES service in two modes that are PWE3 and MEF8. The Pseudo Wire Emulation Edge-to-Edge (PWE3) mode of the Internet Engineering Task Force (IETF) implements circuit emulation over the IP network, namely, TDMoIP, based on the IP address.
Page 64: Table 3-3 Configuration Data Of The Gpon Ces Service
ZXA10 C300 Configuration Manual (CLI) Parameter Value Range augno 1 (STM-1 interface) 1–2 (STM-4 interface) tug-3 1–3 tug-2 1–7 1–3 Configuration Data Table 3-3 lists the configuration data of the GPON CES service. Table 3-3 Configuration Data of the GPON CES Service...
Page 65: Chapter 3 Ces Service Configuration
GPON CES service. Figure 3-1 Configuration Flowchart of the GPON CES Service Steps 1. In GPON configuration mode, configure the T-CONT bandwidth profile. ZXAN(config)#gpon ZXAN(config-gpon)#profile tcont 6M type 1 fixed 6000 [Successful] ZXAN(config-gpon)#exit SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 66 ZXA10 C300 Configuration Manual (CLI) 2. In OLT interface configuration mode, authenticate the ONU. ZXAN(config)#interface gpon-olt_1/5/1 ZXAN(config-if)#onu 2 type ZTE-F621 sn ZTEG80000001 [Successful] ZXAN(config-if)#exit 3. In ONU interface configuration mode, configure the T-CONT and GEM port. ZXAN(config)#interface gpon-onu_1/5/1:2 ZXAN(config-if)#tcont 1 name T1 profile 6M...
Page 67 Source Mac Address: 0015.EB72.001A Source IP Address : 192.192.192.24 Note: When the PW CVLAN is not configured, the ZXA10 C300 allocates a CVLAN ID to the PW automatically. 8. In ONU interface configuration mode, configure the service port VLAN. ZXAN(config)#interface gpon-onu_1/5/1:2...
Page 68 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 69: Chapter 4 P2P Service Configuration
Table of Contents Configuring the P2P Service..................4-1 4.1 Configuring the P2P Service The ZXA10 C300 are connected ONUs or other Ethernet devices through the interface card. After you configure the P2P service, the subscribers can enjoy the data, multicast, VoIP service.
Page 70: Table 4-1 P2P Service Configuration Data
ZXAN(config-if)#service-port 3 user-vlan 301 vlan 301 ZXAN(config-if)#exit 3. (Optional) Enable global IGMP protocol. ZXAN(config)#igmp enable Note: By default, the global IGMP protocol is enabled on the ZXA10 C300. 4. Configure IGMP parameters on service port. ZXAN(config)#interface gei_1/5/1 ZXAN(config-if)#igmp fast-leave enable ZXAN(config-if)#exit 5.
Page 71 Ethernet interfaces. Note: Usually, in the P2P service, the uplink card is the 9U-height Ethernet interface card GDFO. In DHCP snooping configuration, only the 4.5U-height uplink cards can be used for uplink. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 72 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 73: Chapter 5 Vlan Configuration
LAN into several logical network segments. The IEEE issued the IEEE 802.1q standard in 1999 to normalize the VLAN solution. The ZXA10 C300 supports 4094 VLANs. Table 5-1 lists the VLAN specifications.
Page 74: Configuring The Service Port Vlan
ZXA10 C300 Configuration Manual (CLI) Note: When you configure the uplink port VLAN, the system will automatically create the corresponding VLAN. – End of Steps – 5.2 Configuring the Service Port VLAN By configuring the service port VLAN on the PON ONU interface, you can implement VLAN translation at the ONU level.
Page 75: Configuring The Cross-Connection Vlan
3. In VLAN configuration mode, configure the VLAN to the cross-connection VLAN. ZXAN(config)#vlan 5 ZZXAN(config-vlan5)#xconnect enable cvlan 3 4. (Optional) Query the cross-connection VLAN configuration. ZXAN(config-vlan5)#show vlan-xconnect detail User-Port Uplink-Port Svlan Cvlan Status ------------------------------------------------------------ gpon-onu_1/5/1:1 vport 1 gei_1/21/1 – End of Steps – SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 76 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 77: Chapter 6 Iptv Configuration
Configuration of the OLT multicast protocol mode The ZXA10 C300 supports the IPv4 and IPv6 multicast dual protocol stack so it can be flexibly configured to accept/drop packets of various protocols. Three working modes (Snooping/Router/Proxy) can be configured based on the multicast VLAN.
Page 78: Configuring The Igmp Mvlan
ZXA10 C300 Configuration Manual (CLI) Supports Multicast Listener Discovery (MLD) v1/v2. Supports IGMP Snooping/Proxy/Router. Supports MLD Snooping/Proxy. Supports 8K multicast entries. Supports 256 multicast VLANs. Supports Channel Access Control (CAC). Supports channel preview. Supports Call Detail Record (CDR). Table of Contents Configuring the IGMP MVLAN..................6-2...
Page 79 IGMP global parameters: --------------------------------------- IGMP is globally enable. Span vlan is enable. Host tracking is disable. IGMP log is disable. General query gemport mode is unicast. Prejoin interval is 120(second). 13. (Optional) Query the MVLAN. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 80 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#show igmp mvlan Total Num is 1. Status Work-mode GroupFilter Filter-mode ActGroups HostVersion ------------------------------------------------------------------------ enable proxy disable asmssm ZXAN(config)#show igmp mvlan 200 Protocol packet's priority is 0 (in proxy/spr mode) Act Port is 0. Host ip is 192.168.2.14.
Page 81: Configuring The Mld Mvlan
4. Enable MLD span VLAN function. ZXAN(config)#mld span-vlan enable 5. Configure the MVLAN. ZXAN(config)#mld mvlan 200 6. Configure the MVLAN working mode. ZXAN(config)#mld mvlan 200 work-mode proxy 7. Configure the MVLAN host version. ZXAN(config)#mld mvlan 200 host-version v1 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 82 ZXA10 C300 Configuration Manual (CLI) 8. Configure the MVLAN multicast group. ZXAN(config)#mld mvlan 200 group ff1e::0101 to ff1e::0103 9. Configure MVLAN source port. ZXAN(config)#mld mvlan 200 source-port gei_1/21/1 10. Configure the MVLAN receive port. ZXAN(config)#mld mvlan 200 receive-port gpon-onu_1/5/1:1 vport 1 11.
Page 83: Configuring The Iptv Package
Channel 0: stv001 (watch) Channel 1: stv002 (watch) Channel 2: stv003 (preview) Steps 1. Configure the IPTV channel. ZXAN(config)#iptv channel mvlan 200 group 224.1.1.1 to 224.1.1.3 source-address 10.1.1.1 prename stv 2. Create the IPTV package. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 84: Configuring The Port Iptv Right
By configuring the IPTV right for port, you can apply the IPTV package to the subscriber port to implement the access control of the IPTV channel. Prerequisite The MVLAN has been configured. The IPTV package has been configured. Context The ZXA10 C300 supports 2-level CAC. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 85 ZXAN(config)#show iptv control : enable : 192.168.0.119 4. (Optional) Query the IPTV port configuration. ZXAN(config)#show iptv interface gpon-onu_1/5/1:1 auth-mode : auth right-mode: package cdrstatus : enable service : IN_SERVICE – End of Steps – SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 86 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 6-10 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 87: Chapter 7 Qos Configuration
Via flexible configuration and application of the QoS attributes, the carrier can provide effective differentiated services and implement and assure the committed service quality. Service Specifications The ZXA10 C300 supports the following QoS operations: Precedence remarking Queue scheduling Queue mapping...
Page 88: Configuring Dscp-Cos Remarking
ZXA10 C300 Configuration Manual (CLI) 7.1.2 Configuring DSCP-CoS Remarking Using the DSCP-to-CoS remarking profile, you can remark the packet CoS priority according to the its DSCP value. Steps 1. In global configuration mode, configure the DSCP-to-CoS remarking profile. ZXAN(config)#qos dscp-to-cos-profile test 3 to 6 2.
Page 89: Configuring Dscp Remarking
Using the DSCP remark profile, you can remark the packet DSCP priority according to the its original DSCP value. Steps 1. In global configuration mode, configure the DSCP remarking profile. ZXAN(config)#qos dscp-to-dscp-profile test 3 to 13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 90: Configuring Queue Scheduling
ZXA10 C300 Configuration Manual (CLI) 2. In Ethernet interface mode, apply the DSCP remarking profile. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#qos dscp dscp-remark test 3. Configure trust DSCP on the interface. ZXAN(config-if)#qos trust dscp 4. (Optional) Query the QoS configuration on the interface.
Page 91: Configuring Traffic Shaping
By default, traffic shaping is disabled. Steps 1. In Ethernet interface mode, configure traffic shaping. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#qos traffic-shape rate-limit 1280 bucket-size 512 2. (Optional) Query the QoS configuration on the interface. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 92: Configuring The Mapping Relation From Cos To Local Queues
ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#show qos interface gei_1/21/1 qos traffic-shape rate-limit 1280 bucket-size 512 – End of Steps – 7.1.7 Configuring the Mapping Relation From CoS to Local Queues This section describes how to configure the mapping relation from the Ethernet packet CoS to local queues.
Page 93: Configuring Queue Mapping
ZXAN(config)#traffic-profile test ip cir 10240 cbs 1000 pir 20480 pbs 1000 2. In OLT interface configuration mode, apply the traffic profile. ZXAN(config)#interface gpon-olt_1/5/1 ZXAN(config-if)#traffic-profile test direction egress 3. (Optional) Query the QoS traffic profile. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 94: Onu Interface Qos Configuration
ZXA10 C300 Configuration Manual (CLI) ZXAN(config-if)#show traffic-profile test ----------------------------------------------------------------- profile name : TEST profile detail ----------------------------------------------------------------- basic traffic type : ip committed information rate : 10240 kbps committed burst size : 1000 kbytes peak information rate : 20480 kbps peak burst size...
Page 95: Configuring The Default Cos
When the vport trusts and the default CoS is not configured with the override operation, the CoS in packets is modified according to the mapping relation in the profile after the CoS remarking profile is configured. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 96: Configuring Dscp To Cos Remarking
ZXA10 C300 Configuration Manual (CLI) Steps 1. In global configuration mode, configure the CoS remarking profile. ZXAN(config)#qos cos-to-cos-profile test cos0 3 2. In ONU interface configuration mode, apply the CoS remarking profile. ZXAN(config)#interface gpon-onu_1/5/1:1 ZXAN(config-if)#qos cos cos-remark test vport 1 ZXAN(config-if)#qos trust cos vport 1 3.
Page 97: Configuring Egress Cos Remarking
– End of Steps – 7.3.7 Configuring Egress DSCP to CoS Remarking Using the DSCP-to-CoS remarking profile, you can remark packet’s egress CoS priority according to its DSCP value on the ONU virtual port (vport). 7-11 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 98: Configuring Cos Filtering
ZXA10 C300 Configuration Manual (CLI) Context When the vport trusts DSCP, the in packets is modified according to the mapping relation in the profile after the egress DSCP remarking profile is configured. Steps 1. In global configuration mode, configure the DSCP-to-CoS remarking profile.
Page 99: Configuring Queue Mapping
3. (Optional) Query the QoS queue map profile. ZXAN(config-if)#show qos queue-map-profile test -------------------------------------------------------------- profile name : TEST profile detail : ---------------------------------------- queue-map cos-queue-type queue-number : cos-value cos-queue-map: ---------------------------------------- profile used by: gpon-onu_1/5/1:1:1 – End of Steps – 7-13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 100: Configuring The Traffic Profile
ZXA10 C300 Configuration Manual (CLI) 7.3.11 Configuring the Traffic Profile Using the traffic profile, you can limit the traffic of the GPON ONU virtual port (vport). Steps 1. In global configuration mode, configure the traffic profile. ZXAN(config)#traffic-profile test ip cir 10240 cbs 1000 pir 20480 pbs 1000 2.
Page 101: Chapter 8 Acl Configuration
The last rule in an ACL is an implicit deny rule. One interface supports only one ACL. The ZXA10 C300 supports the following four types of ACLs: Standard ACL The standard ACL is only matched by the source address.
Page 102: Configuring A Standard Acl
ZXA10 C300 Configuration Manual (CLI) 8.1 Configuring a Standard ACL This section describes how to configure a standard ACL and apply it to an Ethernet interface. Configuration Data Table 8-1 lists the configuration data of the standard ACL. Table 8-1 Configuration Data of the Standard ACL...
Page 103: Configuring An Extended Acl
Data ACL number Rule 1 Action: deny Source address: 192.168.1.0/24 Protocol type: TCP, Telnet Rule 2 Permit any TCP and telnet traffic Interface gei_1/21/1 Steps 1. In global configuration mode, create an extended ACL. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 104: Configuring A Layer-2 Acl
ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#acl extended number 101 ZXAN(config-ext-acl)# Note: The extended ACL number ranges from 100 to 199. An extended ACL can be applied to an Ethernet interface only. 2. Configure the ACL rules. ZXAN(config-ext-acl)#rule 1 deny tcp 192.168.1.0 0.0.0.255 eq telnet any...
Page 105: Table 8-3 Configuration Data Of The Layer-2 Acl
If the time range is not configured, the rule is always effective. 3. In Ethernet interface configuration mode, apply the ACL. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#ip access-group 200 in 4. (Optional) Query the ACL configuration. ZXAN(config-if)#show acl 200 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 106: Configuring A Hybrid Acl
ZXA10 C300 Configuration Manual (CLI) acl link number 200 rule 1 deny any ingress 0000.0000.0001 0000.0000.0000 egress any rule 2 permit any ingress any egress any 5. (Optional) Query the interface bound with the ACL. ZXAN(config-if)#show access-list bound Interface Direction Type...
Page 107: Configuring An Ipv6 Hybrid Acl
Status Acl number/name gei_1/21/1 V4HYBD successful – End of Steps – 8.5 Configuring an IPv6 Hybrid ACL This section describes how to configure an IPv6 hybrid ACL and apply it to an Ethernet interface. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 108: Table 8-5 Configuration Data Of The Ipv6 Hybrid Acl
ZXA10 C300 Configuration Manual (CLI) Configuration Data Table 8-5 lists the configuration data of the IPv6 hybrid ACL. Table 8-5 Configuration Data of the IPv6 Hybrid ACL Item Data ACL number Rule 1 Action: deny IP protocol type: TCP Source address: any...
Page 109 3 permit any any any any ingress any egress any 5. (Optional) Query the interface bound with the ACL. ZXAN(config-if)#show access-list bound Interface Direction Type Status Acl number/name gei_1/21/1 V6HYBD successful – End of Steps – SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 110 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 8-10 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 111: Chapter 9 Ntp Configuration
Table of Contents Configuring NTP......................9-1 9.1 Configuring NTP The ZXA10 C300 works in NTP client mode and synchronizes its time with the NTP server. Steps 1. In global configuration mode, enable NTP. ZXAN(config)#ntp enable 2. Configure the NTP server.
Page 112 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 113 Table of Contents Configuring STP.......................10-1 10.1 Configuring STP The ZXA10 C300 supports MSTP and is compatible with SSTP and RSTP. It also supports MSTP ring networking. By default, the ZXA10 C300 uses the MSTP mode. Any one of 10-1 SJ-20130520164529-007|2013-06-30 (R1.0)
Page 114 ZXAN(config-mstp)#name zte 5. Create the MSTP instance. The ZXA10 C300 has only instance 0 that is the common and internal spanning tree (CIST) in SSTP and RSTP modes. In MSTP mode, instance 0 exists by default and cannot be deleted.
Page 115: Chapter 10 Stp Configuration
Max-Age 20 sec Forward-Delay 15 sec; Max-Hops Message-Age 0 sec; RemainHops Interface Prio.Nbr Name Port ID Cost Role LinkType Bound --------------------------------------------------------------------------- gei_1/22/1 128.42 20000 Discard Designated MSTP – End of Steps – 10-3 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 116 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 10-4 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 117: Chapter 11 Dhcp Configuration
The ZXA10 C300 works as a DHCP server to allocate IP addresses for users. DHCP client (including IPv6 DHCP client) The ZXA10 C300 works as a DHCP client. It requires an IP address from the specified DHCP server, so that users can access it through SNMP.
Page 118: Configuring Dhcp Server
------------------------------- enable – End of Steps – 11.2 Configuring DHCP Server After you configure the DHCP server function, the ZXA10 C300 can work as a DHCP server to allocate IP addresses to subscribers. Configuration Data Table 11-2 lists the configuration data of the DHCP server.
Page 119: Table 11-2 Configuration Data Of Dhcp Server
ZXAN(config-dhcp-pool)#dns-server 10.10.1.2 6. Configure the default route. ZXAN(config-dhcp-pool)#default-router 10.10.1.254 ZXAN(config-dhcp-pool)#exit 7. Configure the DHCP policy. ZXAN(config)#ip dhcp policy dhcppy 1 ZXAN(config-dhcp-policy)#dhcp-pool dhcppool1 ZXAN(config-dhcp-policy)#exit 8. In management interface mode, configure the DHCP mode and policy. 11-3 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 120: Configuring Dhcp Client
State Expiration – End of Steps – 11.3 Configuring DHCP Client The ZXA10 C300 can work as a client to acquire an IP address from a DHCP server. Configuration Data Table 11-3 lists the configuration data of the DHCP client.
Page 121 6. (Optional) In the administrator mode, configure the DHCP client to obtain IP address again. ZXAN#renew dhcp vlan 100 7. (Optional) In the administrator mode, configure the DHCP client to release addresses. ZXAN#release dhcp vlan 100 – End of Steps – 11-5 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 122 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 11-6 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 123: Chapter 12 Uplink Protection Configuration
Chapter 12 Uplink Protection Configuration The ZXA10 C300 adopts the dual uplink protection mechanism to ensure the service stability. When the physical connection between the ZXA10 C300 and upper-layer equipment is broken and the services are interrupted, the device will automatically switch the services to the standby line to restore the services quickly.
Page 124 Member ports must operate in full duplex mode, and the working rates and VLAN attributes must be consistent. The logical port formed by link aggregation on the ZXA10 C300 is called smartgroup. Smartgroup has the same default VLAN attributes as a common Ethernet port.
Page 125 7. In uplink interface configuration mode, add the port to the aggregation group and set port aggregation mode to active. 12-3 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 126 ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#smartgroup 1 mode active Note: The ZXA10 C300 supports the following three port aggregation modes: On: Static aggregation trunk. The two ends of the aggregation need to be set to the on mode. Active: LACP active negotiation mode...
Page 127: Configuring Uaps
Context The ZXA10 C300 supports the uplink automatic protection switching (UAPS) function. The system periodically checks the working status of the uplink port. When the system detects that the link of the working port is disconnected or the link is not available due to link quality degradation, it switches the services to the standby port automatically and without interrupting the services.
Page 128: Configuring Ctla 1+1 Protection
ZXA10 C300 Configuration Manual (CLI) Note: The ZXA10 C300 supports the following two port attributes: Common-port: common port Trunking-port: link aggregation port 6. (Optional) Query the UAPS group configuration. ZXAN(cfg-uaps-1)#show uaps groupid 1 Revertive control enable PortLight control disable Protect-time...
Page 129 ZXAN(config-ces)#sdhprot switch-command group aaa force w2p Note: By default, the ZXA10 C300 can switch between the ports automatically according to the optical port alarms (LOS, LOF, and MS-AIS). To restore automatic alarm switchover, you need to delete the current protection switchover command.
Page 130 ZXA10 C300 Configuration Manual (CLI) Mode: non-revertive Holdoff: Wtr: – End of Steps – 12-8 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 131 The ZXA10 C300 uses the active/standby switchover mechanism and PON port protection mechanism to guarantee stable operation of services. When the backbone fiber connection between the ZXA10 C300 and ONU is broken and the services are interrupted, the device will automatically switch the services to the standby PON port to restore the services quickly.
Page 132: Table 13-1 Pon Protection Configuration Data
ZXA10 C300 Configuration Manual (CLI) Context The ZXA10 C300 supports the following three PON port switchover modes: Force The service is switched to the specified PON port unconditionally. The service can be switched from the protection port to the working port (p2w) or from the working port to the protection port (w2p) forcedly.
Page 133: Chapter 13 Pon Protection Configuration
Work channel interface : gpon-olt_1/5/1 Protect channel interface: gpon-olt_1/5/2 Protection mode: revertive Time to restore(s): Active channel: protect-channel Alarm request: Work channel: OLTSF Protect channel: OLTSF External request: force-switch-to-protection-request – End of Steps – 13-3 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 134 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 13-4 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 135: Chapter 14 Access Security Configuration
Configuration Access security configuration can assure the safety of subscriber accounts, prevent illegal users from accessing the device, and illegal user-side packets from attacking the device. The ZXA10 C300 supports the following access security features: Port identification MAC address anti-spoofing...
Page 136: Table 14-1 Configuration Data Of Port Identification
ZXA10 C300 Configuration Manual (CLI) Context When subscribers access the Internet in PPPoE Intermediate Agent, DHCPv4 Layer-2 Relay Agent, DHCPv6 Layer-2 Relay Agent, or Line Identification Option (LIO) mode, the system uses the corresponding agent to locate port. The system sends the packets with port information to authentication servers to bind subscribers accounts and circuits.
Page 137: Configuring The Dhcpv4 Layer-2 Relay Agent (Dhcpv4L2Ra)
: REMOTE-ID – End of Steps – 14.1.2 Configuring the DHCPv4 Layer-2 Relay Agent (DHCPv4L2RA) When DHCPv4L2RA is enabled, the ZXA10 C300 adds DHCPv4L2RA Option 82 field to the upstream DHCP packets. Context The DHCPv4L2RA Option 82 field contains CID and RID, which includes the shelf number, slot number, and port number.
Page 138: Configuring The Pppoe Intermediate Agent (Pppoe-Ia)
Remote-id : REMOTE-ID //where, 10 is the original user VLAN. 14.1.3 Configuring the PPPoE Intermediate Agent (PPPoE-IA) When PPPoE-IA is enabled, the ZXA10 C300 adds port information to the upstream PPPoE-IA packets. Context When users access the Internet in PPPoE mode, the ZXA10 C300 uses PPPoE-IA to locate port.
Page 139: Configuring The Dhcpv6 Layer-2 Relay Agent (Dhcpv6L2Ra)
REMOTE-ID //where, 10 is original user VLAN. 14.1.4 Configuring the DHCPv6 Layer-2 Relay Agent (DHCPv6L2RA) When DHCPv6L2RA is enabled, the ZXA10 C300 adds DHCPv6L2RA Option 18 and Option 37 fields to the upstream DHCP packets. Context The option 18 field includes CID , and the option 37 field includes RID, which provides the physical information such as the shelf number, slot number, and port number.
Page 140: Configuring The Ndp Line Identification Option (Ndp-Lio)
ZXA10-C300/ZTE eth 5/1/1/0/1:10 Option 37: REMOTE-ID //where, 10 is original user VLAN. 14.1.5 Configuring the NDP Line Identification Option (NDP-LIO) When NDP-LIO is enabled, the ZXA10 C300 adds LIO field to the upstream NDP packets. 14-6 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 141: Table 14-5 Configuration Data Of Ndp-Lio
: 100 4. (Optional) Query the interface configuration of NDP-LIO. ZXAN(config)#show ndp-lio port gpon-onu_1/5/1:1 vport 1 Vport ndp-lio status Trust Policy gpon-onu_1/5/1:1 enable true replace – End of Steps – 14-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 142: Mac Address Anti-Spoofing Configuration
//where, 10 is original user VLAN. 14.2 MAC Address Anti-Spoofing Configuration The ZXA10 C300 supports the MAC address anti-spoofing function to prevent malicious MAC address spoofing, which affects the network security. The ZXA10 C300 MAC address anti-spoofing function has the following features: This function constrains the user port that learns the MAC address.
Page 143: Configuring The Service Gateway Mac Anti-Spoofing
MAC address learning between uplink ports. Context The ZXA10 C300 supports the following features by service gateway MAC anti-spoofing: A MAC address learnt by a user port can be learnt by an uplink port as well.
Page 144: Configuring The Arp Anti-Spoofing
ARP table, the ZXA10 C300 checks whether the addresses are the same. If they are different, the ZXA10 C300 considers the packet as an ARP spoofing behavior and discards it. anti-spoofing function can be configured with up to 256 VLANs.
Page 145: Configuring The Split Horizon
14.4 Configuring the Split Horizon When user communication control is enabled, only subscribers in the specific VLAN and SVLAN can communicate with each other. Context The ZXA10 C300 supports the following split horizon features: Subscriber separation/intercommunication Subscriber intercommunication based on SVLAN and CVLAN Steps 1.
Page 146: Configuring The Ip Source Guard
IP source guard supports IP/MAC anti-spoofing and access security management based on the service port. The ZXA10 C300 supports IP source guard on both IPv4 and IPv6. The legal IPv4 subscribers are managed through either the DHCP snooping table or static IP addresses.
Page 147: Configuring Mff
The gateway then forwards the flows to implement layer-3 interworking between subscribers. The gateway can analyze traffic between subscribers to prevent malicious attacks. Steps 1. Enable MFF. ZXAN(config)#ip-service mac-forced-forwarding enable 14-13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 148: Configuring Arp Proxy
PON port. Context By default, the ZXA10 C300 services on different ONUs under the same PON port are isolated. When a service, such as VoIP, requires interworking between the subscribers under the same PON port, the ZXA10 C300 uses the ARP proxy function to achieve interworking between the subscribers in the same VLAN and same network segment under the same PON port.
Page 149: Chapter 15 System Security Configuration
Configuration System security configuration can prevent illegal network-side packets from attacking devices, thus to ensure stable running of the devices. The ZXA10 C300 supports the following system security features: Secure Shell (SSH) Terminal Access Controller Access-Control (TACACS+) Remote Authentication Dial In User Service (RADIUS)
Page 150: Figure 15-1 Quick Connect Dialog Box
ZXA10 C300 Configuration Manual (CLI) 2. Configure the SSH server protocol version. ZXAN(config)#ssh server version 2 3. Configure the SSH server authentication mode. ZXAN(config)#ssh server authentication mode local 4. Configure the SSH server authentication type. ZXAN(config)#ssh server authentication type pap 5.
Page 151: Configuring Tacacs
Chapter 15 System Security Configuration Figure 15-2 SSH Login Window Note: The hostname is the in-band/out-of-band NM IP address of the ZXA10 C300. 15.2 Configuring TACACS+ TACACS+ ensures data safety of the ZXA10 C300 by implementing safety authentication and authorization for remote subscribers who access the ZXA10 C300.
Page 152: Configuring Radius
ZXA10 C300 Configuration Manual (CLI) In-band NM mode (The ZXA10 C300 is connected to the TACACS+ server through the in-band NM channel.) ZXAN(config)#tacacs-server host 1.2.2.3 Out-of-band NM mode (The ZXA10 C300 is connected to the TACACS+ server through the out-of-band NM channel.) ZXAN(config)#tacacs-server host vrf mng 1.2.2.3...
Page 153: Configuring Management Acl
6. (Optional) Configure the route. ZXAN(config-authgrp-1)#ip mng ZXAN(config-authgrp-1)#exit Note: When the ZXA10 C300 is connected to the RADIUS server through the in-band NM channel, you can skip this step. 7. Configure the authentication group. ZXAN(config)#aaa authentication login default rds-group 1 8.
Page 154: Configuring Control Panel Safety
ZXAN(config)#line telnet access-class 10 – End of Steps – 15.5 Configuring Control Panel Safety After you configure control panel safety, the ZXA10 C300 can limit the protocol packet rate and prevent DoS packet attacks. Context Control panel safety includes the following three functions: Rate limit of protocol packets Different rate limits are set for packets of different protocols.
Page 155 Chapter 15 System Security Configuration ZXAN(control-panel)#show control-panel anti-dos black-table ----------------------------MP BLACK TABLE------------------------------------ mac-address vlan port onu-sn state PktIn Drop ----------------------------NP BLACK-TABLE------------------------------------ mac-address port onu-sn state PktIn Drop ------------------------------------------------------------------------------- – End of Steps – 15-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 156 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 15-8 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 157: Chapter 16 Mpls Service Configuration
16.1.1 Configuring the Basic MPLS Function In the basic MPLS application, the MPLS forwarding is based on the LDP sessions between routers. Networking Diagram Figure 16-1 shows the networking diagram of the basic MPLS function. 16-1 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 158: Figure 16-1 Networking Diagram Of Basic Mpls Function
ZXA10 C300 Configuration Manual (CLI) Figure 16-1 Networking Diagram of Basic MPLS Function Three ZXA10 C300s are in the same OSPF area and interconnected by the OSPF protocol. Configuration Data Table 16-1 lists the configuration data of the basic MPLS function.
Page 159: Figure 16-2 Configuration Flowchart Of Basic Mpls Function
ZXAN(config-if-vlan10)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 1.1.1.1 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function. ZXAN(config)#mpls ldp router-id loopback1 ZXAN(config)#vlan-reserve 4090 vpn 16-3 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 160 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#mpls ip 7. Save configuration data. Configuration on C300-2. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 11 tag...
Page 161: Configuring The Static Lsp
Execute the command ping mpls ipv4 3.3.3.3 32 repeat 1000 on C300-1. The ping is successful. 16.1.2 Configuring the Static LSP The static LSP is used in MPLS L2VPN. Networking Diagram Figure 16-3 shows the networking diagram of the static Label Switched Path (LSP) configuration. 16-5 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 162: Figure 16-3 Networking Diagram Of Static Lsp Configuration
ZXA10 C300 Configuration Manual (CLI) Figure 16-3 Networking Diagram of Static LSP Configuration The Label Distribution Protocol (LDP) is running on the four ZXA10 C300s. Configure two static LSPs between C300-1 and C300-3. The static LSP from C300-1 to C300-3 is: C300-1 > C300-2 > C300-3.
Page 163 IP address: 13.1.1.1/24 L3 interface 2 VLAN ID: 12 Interface: gei_1/21/2 IP address: 12.1.1.2/24 Static LSP (C300-3 to C300-1) Destination IP address: 1.1.1.1/32 Next hop IP address: 13.1.1.2/24 Out label: 1040004 In label: 1040005 16-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 164: Figure 16-4 Configuration Flowchart Of Static Lsp
ZXA10 C300 Configuration Manual (CLI) Configuration Flow Figure 16-4 shows the configuration flowchart of the static LSP. Figure 16-4 Configuration Flowchart of Static LSP Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2.
Page 165 ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.2 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 11.1.1.1 255.255.255.0 ZXAN(config-if-vlan11)#exit 16-9 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 166 ZXA10 C300 Configuration Manual (CLI) 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#mpls ip ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#mpls ip ZXAN(config-if-vlan11)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 2.2.2.2 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#network 11.1.1.0 0.0.0.255 area 0.0.0.0...
Page 167 ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 12 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interfaces. ZXAN(config)#interface vlan 12 ZXAN(config-if-vlan12)#ip address 12.1.1.2 255.255.255.0 ZXAN(config-if-vlan12)#exit ZXAN(config)#interface vlan 13 ZXAN(config-if-vlan13)#ip address 13.1.1.1 255.255.255.0 ZXAN(config-if-vlan13)#exit 16-11 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 168: Configuring The Ldp Frr Function
ZXA10 C300 Configuration Manual (CLI) 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 12 ZXAN(config-if-vlan12)#mpls ip ZXAN(config-if-vlan12)#exit ZXAN(config)#interface vlan 13 ZXAN(config-if-vlan13)#mpls ip ZXAN(config-if-vlan13)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 4.4.4.4 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 12.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#network 13.1.1.0 0.0.0.255 area 0.0.0.0...
Page 169: Figure 16-5 Networking Diagram Of Ldp Frr Configuration
VLAN ID: 13 Interface: gei_1/21/2 IP address: 13.1.1.12/24 Active route Destination IP address: 3.3.3.3/32 Next hop IP address: 10.1.1.2/24 Backup route Destination IP address: 3.3.3.3/32 Next hop IP address: 13.1.1.1/24 Tag value: 200 Priority: 60 16-13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 170 ZXA10 C300 Configuration Manual (CLI) Item Data C300-2 Loopback interface ID: 1 IP address: 2.2.2.2/32 L3 interface 1 VLAN ID: 11 Interface: gei_1/21/1 IP address: 11.1.1.1/24 L3 interface 2 VLAN ID: 10 Interface: gei_1/21/2 IP address: 10.1.1.2/24 C300-3 Loopback interface ID: 1 IP address: 3.3.3.3/32...
Page 171: Figure 16-6 Configuration Flowchart Of Ldp Frr Function
3. Configure the IP address of the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.1 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 13 ZXAN(config-if-vlan13)#ip address 13.1.1.2 255.255.255.0 ZXAN(config-if-vlan13)#exit 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#mpls ip 16-15 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 172 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 13 ZXAN(config-if-vlan13)#mpls ip ZXAN(config-if-vlan13)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 1.1.1.1 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#network 13.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function.
Page 173 ZXAN(config-if-vlan12)#ip address 12.1.1.1 255.255.255.0 ZXAN(config-if-vlan12)#exit 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#mpls ip ZXAN(config-if-vlan11)#exit ZXAN(config)#interface vlan 12 ZXAN(config-if-vlan12)#mpls ip ZXAN(config-if-vlan12)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 16-17 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 174 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-router)#network 3.3.3.3 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 11.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#network 12.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function. ZXAN(config)#mpls ldp router-id loopback1 ZXAN(config)#mpls ip 7. Save the configuration data. Configuration on C300-4.
Page 175: Configuring The Ldp Gr Function
LDP GR function. Table 16-4 Configuration Data of LDP GR Function Item Data C300-1 Loopback interface ID: 1 IP address: 1.1.1.1/32 L3 interface VLAN ID: 10 Interface: gei_1/21/1 IP address: 10.1.1.1/24 Grace period 180 s 16-19 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 176: Figure 16-8 Configuration Flowchart Of Ldp Gr Function
ZXA10 C300 Configuration Manual (CLI) Item Data C300-2 Loopback interface ID: 1 IP address: 2.2.2.2/32 L3 interface 1 VLAN ID: 11 Interface: gei_1/21/1 IP address: 11.1.1.1/24 L3 interface 2 VLAN ID: 10 Interface: gei_1/21/2 IP address: 10.1.1.2/24 Grace period 180 s...
Page 177 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interfaces. 16-21 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 178 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.2 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 11.1.1.1 255.255.255.0 ZXAN(config-if-vlan11)#exit 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#mpls ip ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#mpls ip ZXAN(config-if-vlan11)#exit 5.
Page 179: Vpls Configuration
It allows geographically dispersed sites to share an Ethernet broadcast domain by connecting sites through PWs. Networking Diagram Figure 16-9 shows the networking diagram of the basic Virtual Private LAN Service (VPLS). 16-23 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 180 ZXA10 C300 Configuration Manual (CLI) Figure 16-9 Networking Diagram of Basic VPLS ONU1 and ONU2 are in the same VPLS network. These two ONUs communicate with each other through the Pseudo-Wires (PWs) based on the sessions. Configuration Data Table 16-5 lists the configuration data of the basic VPLS.
Page 181 A Customer Instance Port (CIP) is a logical interface that correlates to an L2VPN service instance, that is, an Attachment Circuit (AC). The data on a CIP is a certain service flow, which is specified by a class map, from a UNI. 16-25 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 182: Figure 16-10 Configuration Flowchart Of Basic Vpls
ZXA10 C300 Configuration Manual (CLI) Configuration Flow Figure 16-10 shows the configuration flowchart of the basic VPLS. Figure 16-10 Configuration Flowchart of Basic VPLS Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)# address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2.
Page 183 11. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect vpls-vfi ZXAN(config-cip1)#exit 12. Save the configuration data. Configuration on C300-2. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 ZXAN(config-loopback1)#exit 16-27 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 184 ZXA10 C300 Configuration Manual (CLI) 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.2 255.255.255.0...
Page 185 ZXAN(config-vfi)#mpls xconnect pw 1and1000pw ZXAN(config-vfi)#exit 10. Configure the class map. ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 11. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect vpls-vfi ZXAN(config-cip1)#exit 12. Save the configuration data. 16-29 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 186: Configuring The Full-Mesh Vpls
ZXA10 C300 Configuration Manual (CLI) Result Two ONUs can ping each other successfully. 16.2.2 Configuring the Full-Mesh VPLS To connect all of the customer LANs, full mesh connectivity is required. LDP is used for full mesh establishment for VPLS. Networking Diagram Figure 16-11 shows the networking diagram of the full-mesh VPLS.
Page 187: Table 16-6 Configuration Data Of Full-Mesh Vpls
ID: 1 IP address: 2.2.2.2/32 L3 interface 1 VLAN ID: 11 Interface: gei_1/21/1 IP address: 10.1.1.1/24 L3 interface 2 VLAN ID: 12 Interface: gei_1/21/2 IP address: 20.1.1.2/24 Reserved VPN VLAN VLAN ID: 4090 16-31 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 188 ZXA10 C300 Configuration Manual (CLI) Item Data PW 1 Name: 1and1000pw Mode: dynamic pwe3 Type: ethernet-vlan Peer: 1.1.1.1 Router ID: 1.1.1.1 VC ID: 1000 PW 2 Name: 3and1000pw Mode: dynamic pwe3 Type: ethernet-vlan Peer: 3.3.3.3 Router ID: 3.3.3.3 VC ID: 1000...
Page 189 A CIP is a logical interface that correlates to an L2VPN service instance, that is, AC. The data on a CIP is a certain service flow, which is specified by a class map, from a UNI. Configuration Flow Figure 16-12 shows the configuration flowchart of the full-mesh VPLS. 16-33 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 190: Figure 16-12 Configuration Flowchart Of Full-Mesh Vpls
ZXA10 C300 Configuration Manual (CLI) Figure 16-12 Configuration Flowchart of Full-Mesh VPLS Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag...
Page 191 ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet-vlan ZXAN(config-pw)#peer 3.3.3.3 router-id 3.3.3.3 vcid 1000 ZXAN(config-pw)#exit 9. Configure the VFI. ZXAN(config)#vfi fullmesh-vfi ZXAN(config-vfi)#mpls xconnect pw 2and1000pw ZXAN(config-vfi)#mpls xconnect pw 3and1000pw ZXAN(config-vfi)#exit 10. Configure the class map. 16-35 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 192 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 11. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect fullmesh-vfi ZXAN(config-cip1)#exit 12. Save the configuration data. Configuration on C300-2. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 ZXAN(config-loopback1)#exit 2.
Page 193 12. Save the configuration data. Configuration on C300-3. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 3.3.3.3 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interface. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 12 tag 16-37 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 194 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 30.1.1.2 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 12 ZXAN(config-if-vlan12)#ip address 20.1.1.1 255.255.255.0 ZXAN(config-if-vlan12)#exit 4. Enable the MPLS on the VLAN interfaces.
Page 195: Configuring The Hierarchical Vpls
HVPLS may also be used to join two VPLS mesh structures together. Networking Diagram Figure 16-13 shows the networking diagram of the Hierarchical VPLS (HVPLS). 16-39 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 196: Figure 16-13 Hpvls Networking Diagram
ZXA10 C300 Configuration Manual (CLI) Figure 16-13 HPVLS Networking Diagram ONU1, ONU2, and ONU3 are in the same VPLS network. ONU1 and ONU2 are connected to the VPLS network through the User-facing (UPE), while ONU3 is connected to the VPLS through the PE. The Network PE (NPE) communicates with the UPE through a spoke sessions.
Page 197 Type: ethernet-vlan Peer: 3.3.3.3 Router ID: 3.3.3.3 VC ID: 1000 Name: hvpls-vfi PW1: 1and1000pw (spoke) PW2: 3and1000pw Class map Name: classmap1000 SVLAN ID: 1000 Index: 1 Service type: ethernet class-map Class map: classmap1000 16-41 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 198 ZXA10 C300 Configuration Manual (CLI) Item Data C300-3 Loopback interface ID: 1 IP address: 3.3.3.3/32 L3 interface VLAN ID: 11 Interface: gei_1/21/2 IP address: 11.1.1.2/24 Reserved VPN VLAN VLAN ID: 4090 Name: 2and1000pw Mode: dynamic pwe3 Type: ethernet-vlan Peer: 2.2.2.2 Router ID: 2.2.2.2...
Page 199: Figure 16-14 Hvpls Configuration Flowchart
ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.1 255.255.255.0 4. Enable the MPLS on the VLAN interface. ZXAN(config-if-vlan10)#mpls ip ZXAN(config-if-vlan10)#exit 16-43 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 200 ZXA10 C300 Configuration Manual (CLI) 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 1.1.1.1 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function. ZXAN(config)#vlan-reserve 4090 vpn ZXAN(config)#ip mpls-forwarding enable ZXAN(config)#mpls ldp router-id loopback1 ZXAN(config)#mpls ip 7.
Page 201 8. Configure the VC. ZXAN(config)#pw 1and1000pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet-vlan ZXAN(config-pw)#peer 1.1.1.1 router-id 1.1.1.1 vcid 1000 ZXAN(config)#pw 3and1000pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet-vlan ZXAN(config-pw)#peer 3.3.3.3 router-id 3.3.3.3 vcid 1000 ZXAN(config-pw)#exit 16-45 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 202 ZXA10 C300 Configuration Manual (CLI) 9. Configure the VFI. ZXAN(config)#vfi hvpls-vfi ZXAN(config-vfi)#mpls xconnect pw 1and1000pw spoke ZXAN(config-vfi)#mpls xconnect pw 3and1000pw ZXAN(config-vfi)#exit 10. Configure the class map. ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 11. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000...
Page 203: Configuring The Vpws
IP/MPLS networks. VLL uses the encapsulation for transporting Ethernet traffic over an MPLS tunnel across an IP/MPLS backbone. Networking Diagram Figure 16-15 shows the networking diagram of the VPWS. 16-47 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 204 ZXA10 C300 Configuration Manual (CLI) Figure 16-15 VPWS Networking Diagram Two ZXA10 C300s and a router are in the same OSPF area. ONU1 and ONU2 access the two PEs (ZXA10 C300s) through the VLAN. The two ONUs communicate with each other through the VPWS based on the sessions.
Page 205 A CIP is a logical interface that correlates to an L2VPN service instance, that is, an AC. The data on a CIP is a certain service flow, which is specified by a class map, from a UNI. Configuration Flow Figure 16-16 shows the configuration flowchart of the VPWS. 16-49 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 206: Figure 16-16 Configuration Flowchart Of Vpws
ZXA10 C300 Configuration Manual (CLI) Figure 16-16 Configuration Flowchart of VPWS Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interface. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3.
Page 207 ZXAN(config-cip1)#xconnect zte-vpws ZXAN(config-cip1)#exit 12. Save the configuration data. Configuration on C300-2. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 16-51 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 208 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.2 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 11.1.1.1 255.255.255.0 ZXAN(config-if-vlan11)#exit 4.
Page 209 ZXAN(config-vll)#mpls xconnect pw 1and1000pw ZXAN(config-vll)#exit 10. Configure the class map. ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 11. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect zte-vpws ZXAN(config-cip1)#exit 12. Save the configuration data. 16-53 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 210: Pwe3 Configuration
ZXA10 C300 Configuration Manual (CLI) Result The two ONUs can ping each other successfully. 16.4 PWE3 Configuration 16.4.1 Configuring the Basic PWE3 Service In the basic PWE3 application, the PEs transparently transmit the services of CEs through the PWs. Background Information...
Page 211 Mode: dynamic pwe3 Type: ethernet Peer: 3.3.3.3 Router ID: 3.3.3.3 ID: 1000 Name: pwe3-vll Type: ethernet PW: 3and1000pw Class map Name: classmap1000 SVLAN ID: 1000 Index: 1 Service type: ethernet class-map Class map: classmap1000 16-55 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 212 ZXA10 C300 Configuration Manual (CLI) Item Data C300-2 Loopback interface ID: 1 IP address: 2.2.2.2/32 L3 interface 1 VLAN ID: 11 Interface: gei_1/21/1 IP address: 11.1.1.1/24 L3 interface 2 VLAN ID: 10 Interface: gei_1/21/2 IP address: 10.1.1.2/24 Reserved VPN VLAN...
Page 213: Figure 16-19 Configuration Flowchart Of Pw Redundancy
ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.1 255.255.255.0 16-57 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 214 ZXA10 C300 Configuration Manual (CLI) 4. Enable the MPLS on the VLAN interface. ZXAN(config-if-vlan10)#mpls ip ZXAN(config-if-vlan10)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 1.1.1.1 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function.
Page 215 ZXAN(config)#mpls ldp router-id loopback1 ZXAN(config)#mpls ip 7. Save the configuration data. Configuration on C300-3. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 3.3.3.3 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. XAN(config)#interface gei_1/21/2 16-59 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 216 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 11.1.1.2 255.255.255.0 4. Enable the MPLS on the VLAN interface. ZXAN(config-if-vlan11)#mpls ip ZXAN(config-if-vlan11)#exit 5. Configure the routing protocol.
Page 217: Configuring Multi-Segment Pws
Table 16-10 Configuration Data of Multi-Segment PWs Item Data C300-1 Loopback interface ID: 1 IP address: 1.1.1.1/32 L3 interface VLAN ID: 10 Interface: gei_1/21/1 IP address: 10.1.1.1/24 Reserved VPN VLAN VLAN ID: 4090 16-61 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 218 ZXA10 C300 Configuration Manual (CLI) Item Data Name: 2and2000pw Mode: static Type: ethernet Peer: 2.2.2.2 Router ID: 2.2.2.2 ID: 2000 Local label: 1042431 Remote label: 1042432 Name: mspw-vll Type: ethernet PW: 2and2000pw Class map Name: classmap2000 SVLAN ID: 2000 Index: 1...
Page 219 A CIP is a logical interface that correlates to an L2VPN service instance, that is, an AC. The data on a CIP is a certain service flow, which is specified by a class map, from a UNI. Configuration Flow Figure 16-21 shows the configuration flowchart of the multi-segment PWs. 16-63 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 220: Figure 16-21 Configuration Flowchart Of Multi-Segment Pws
ZXA10 C300 Configuration Manual (CLI) Figure 16-21 Configuration Flowchart of Multi-Segment PWs Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interface. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3.
Page 221 ZXAN(config-cmap)#match svlan-id 2000 ZXAN(config-cmap)#exit 11. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap2000 ZXAN(config-cip1)#xconnect mspw-vll ZXAN(config-cip1)#exit 12. Save the configuration data. ZXAN(config)#exit ZXAN#write Building configuration......[OK] Configuration on C300-2. 1. Configure the loopback interface. 16-65 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 222 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface.
Page 223 4. Enable the MPLS on the VLAN interface. ZXAN(config-if-vlan11)#mpls ip ZXAN(config-if-vlan11)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 3.3.3.3 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 11.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function. ZXAN(config)#vlan-reserve 4090 vpn 16-67 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 224: Configuring The Tdm Relay Service
ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#ip mpls-forwarding enable ZXAN(config)#mpls ldp router-id loopback1 ZXAN(config)#mpls ip 7. Configure the LDP target session. ZXAN(config)#mpls ldp target-session 2.2.2.2 8. Configure the VC. ZXAN(config)#pw 2and2001pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet ZXAN(config-pw)#peer 2.2.2.2 router-id 2.2.2.2 vcid 2001 ZXAN(config-pw)#exit 9.
Page 225 Name: 3and1000pw Control-word: preferred Name: 3and1000pw Mode: dynamic pwe3 Type: e1 Peer: 3.3.3.3 Router ID: 3.3.3.3 ID: 1000 Name: tdm-vll Type: tdm PW: 3and1000pw Index: 1 PSN local label: 1046016 PSN remote label: 6016 16-69 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 226 ZXA10 C300 Configuration Manual (CLI) Item Data PW local label: 1046015 PW remote label: 6015 Destination MAC address: 0015.eb72.0004 VLAN ID: 1000 MAC address 0015.eb72.0002 RTD slot number F829–1 MAC address 0015.eb72.0004 TDM profile Name: f829 Packet reorder: enable header: enable...
Page 227 Timestamp mode: differential Queue size: 6 TDM service Type: e1Satop Clock source: adaptive Primary clock port: 1 Secondary clock port: 2 Slot: 0/2 PW TDM properties Name: pw_0/2/1 TDM interface: tdm_0/2/1 16-71 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 228 ZXA10 C300 Configuration Manual (CLI) Item Data Number of trunk frames per packet: 1 Time slots: 1–12 TDM profile: f829 PW PSN properties Type: mpls-staticdouble Inbound transport label: 0x1b68 Outbound transport label:0xff9e8 Inbound interworking label: 0x1b67 Outbound interworking label: 0xff9e7 Destination MAC address: 0015.eb72.0003...
Page 229: Figure 16-23 Configuration Flowchart Of Tdm Relay Service
ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interface. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 10 ZXAN(config-if)#ip address 10.1.1.1 255.255.255.0 16-73 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 230 ZXA10 C300 Configuration Manual (CLI) 4. Enable the MPLS on the VLAN interface. ZXAN(config-if)#mpls ip ZXAN(config-if)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 1.1.1.1 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function.
Page 231 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.2 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 11.1.1.1 255.255.255.0 ZXAN(config-if-vlan11)#exit 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#mpls ip 16-75 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 232 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#mpls ip ZXAN(config-if-vlan11)#exit 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 2.2.2.2 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#network 11.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function.
Page 233 3. Configure the TDM service. ZXAN(config-ces)# tdm-service type e1satop clock-source adaptive primary-clock 1 secondary-clock 3 0/2 4. Configure the PW. ZXAN(config-ces)# pw pw_0/2/1 ZXAN(config-ces-pw)# tdm-relation tdm_0/2/1 frame 1 channellist 1-12 tdm-profile -name f829 16-77 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 234: Pw Redundancy Configuration
ZXA10 C300 Configuration Manual (CLI) ZXAN(config-ces-pw)# psn mpls-staticdouble 0x1b68 0xff9e8 0x1b67 0xff9e7 dst-mac 0015.eb72.0003 vlan 1000 priority 7 5. Save the configuration data. ZXAN(config-ces-pw)# end ZXAN# write Result The TDM relay service is successfully configured on both C300s and F829s.
Page 235: Table 16-12 Configuration Data Of Vpls Redundancy
Class map: classmap1000 C300-2 Loopback interface ID ID: 1 IP address: 2.2.2.2/32 L3 interface VLAN ID: 11 Interface: gei_1/21/1 IP address: 10.1.1.1/24 Reserved VPN VLAN VLAN ID: 4090 Name: 1and1000pw Mode: dynamic pwe3 Peer: 1.1.1.1 16-79 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 236 ZXA10 C300 Configuration Manual (CLI) Item Data Router ID: 1.1.1.1 VC ID: 1000 PW redundancy group Name: 2and3vcid1000 PW: 1and1000pw Name: redundancy-vfi PW: 1and1000pw Class map Name: classmap1000 SVLAN ID: 1000 Index: 1 Service type: ethernet class-map Class map: classmap1000...
Page 237: Figure 16-25 Configuration Flowchart Of Vpls Redundancy
1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit 16-81 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 238 ZXA10 C300 Configuration Manual (CLI) 3. Configure the IP address of the VLAN interfaces. ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 30.1.1.1 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 10.1.1.2 255.255.255.0 ZXAN(config-if-vlan11)#exit 4. Enable the MPLS on the VLAN interfaces. ZXAN(config)#interface vlan 10...
Page 239 ZXAN(config-cmap)#exit 12. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect redundancy-vfi ZXAN(config-cip1)#exit 13. Save the configuration data. Configuration on C300-2. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 2.2.2.2 255.255.255.255 16-83 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 240 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interface. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 11 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interface. ZXAN(config)#interface vlan 11 ZXAN(config-if-vlan11)#ip address 10.1.1.1 255.255.255.0 4. Enable the MPLS on the VLAN interface.
Page 241 5. Configure the routing protocol. ZXAN(config)#router ospf 1 ZXAN(config-router)#network 3.3.3.3 0.0.0.0 area 0.0.0.0 ZXAN(config-router)#network 30.1.1.0 0.0.0.255 area 0.0.0.0 ZXAN(config-router)#exit 6. Enable the global MPLS function. ZXAN(config)#vlan-reserve 4090 vpn ZXAN(config)#ip mpls-forwarding enable ZXAN(config)#mpls ldp router-id loopback1 16-85 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 242 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#mpls ip 7. Configure the LDP target session. ZXAN(config)#mpls ldp target-session 1.1.1.1 8. Configure the PW. ZXAN(config)#pw 1and1000pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet ZXAN(config-pw)#peer 1.1.1.1 router-id 1.1.1.1 vcid 1000 ZXAN(config-pw)#exit 9. Configure the PW redundancy group.
Page 243: Configuring The Vll Resilience
Table 16-13 Configuration Data of VLL Resilience Item Data C300-1 Loopback interface ID: 1 IP address: 1.1.1.1/32 L3 interface 1 VLAN ID: 10 Interface: gei_1/21/1 IP address: 30.1.1.1/24 L3 interface 2 VLAN ID: 11 Interface: gei_1/21/2 IP address: 10.1.1.2/24 16-87 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 244 ZXA10 C300 Configuration Manual (CLI) Item Data Reserved VPN VLAN VLAN ID: 4090 PW 1 Name: 2and1000pw Mode: dynamic pwe3 Type: ethernet Peer: 2.2.2.2 Router ID: 2.2.2.2 ID: 1000 PW 2 Name: 3and1000pw Mode: dynamic pwe3 Type: ethernet Peer: 3.3.3.3 Router ID: 3.3.3.3...
Page 245 A CIP is a logical interface that correlates to an L2VPN service instance, that is, an AC. The data on a CIP is a certain service flow, which is specified by a class map, from a UNI. Configuration Flow Figure 16-27 shows the configuration flowchart of the VLL resilience. 16-89 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 246: Figure 16-27 Configuration Flowchart Of Vll Resilience
ZXA10 C300 Configuration Manual (CLI) Figure 16-27 Configuration Flowchart of VLL Resilience Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag...
Page 247 ZXAN(config-pw)#exit ZXAN(config)#pw 3and1000pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet ZXAN(config-pw)#peer 3.3.3.3 router-id 3.3.3.3 vcid 1000 ZXAN(config-pw)#exit 9. Configure the PW redundancy group. Non-negotiation, revertive, 1:1 mode à ZXAN(config)#pw-redundancy-group 2and3vcid1000 ZXAN(config-pw-group)#negotiation disable ZXAN(config-pw-group)#protect-type 1by1 16-91 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 248 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-pw-group)#protect hold-off 0 ZXAN(config-pw-group)#protect mode revertive wtr 1 ZXAN(config-pw-group)#pw 2and1000pw ZXAN(config-pw-group)#second-pw 3and1000pw ZXAN(config-pw-group)#exit Non-negotiation, non-revertive, 1+1 mode à ZXAN(config)#pw-redundancy-group 2and3vcid1000 ZXAN(config-pw-group)#negotiation disable ZXAN(config-pw-group)#protect-type 1plus1 2send2recv ZXAN(config-pw-group)#protect mode non-revertive ZXAN(config-pw-group)#pw 2and1000pw ZXAN(config-pw-group)#second-pw 3and1000pw ZXAN(config-pw-group)#exit Negotiation, master, non-revertive, 1:1 mode à...
Page 249 You may skip this step. Non-negotiation, non-revertive, 1+1 mode à You may skip this step. Negotiation, slave, non-revertive, 1:1 mode à ZXAN(config)#pw-redundancy-group 2and3vcid1000 ZXAN(config-pw-group)#negotiation enable slave ZXAN(config-pw-group)#protect-type 1by1 ZXAN(config-pw-group)#protect mode non-revertive ZXAN(config-pw-group)#pw 1and1000pw 16-93 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 250 ZXA10 C300 Configuration Manual (CLI) ZXAN(config-pw-group)#exit 10. Configure the VLL. ZXAN(config)#vll redundancy-vll ZXAN(config-vll)#mpls xconnect pw 1and1000pw ZXAN(config-vll)#exit 11. Configure the class map. ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 12. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect redundancy-vll...
Page 251 ZXAN(config-vll)#exit 11. Configure the class map. ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 12. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect redundancy-vll ZXAN(config-cip1)#oam-mapping enable ldp ZXAN(config-cip1)#exit 13. Save the configuration data. 16-95 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 252: Configuring The Pw Redundancy And Bfd
ZXA10 C300 Configuration Manual (CLI) Result When the primary PW is disabled, the secondary PW is activated, and the two CEs can ping each other successfully. 16.5.3 Configuring the PW Redundancy and BFD Bidirectional Forwarding Detection (BFD), which can detect the faults on LSPs, is used to help PW redundancy to enhance the stability and reliability of MPLS network.
Page 253: Table 16-14 Configuration Data Of Pw Redundancy And Bfd
Primary PW: 2and1000pw Secondary PW: 3and1000pw BFD session 1 PW name: 2and1000pw Tx interval: 10 ms Rx interval: 10 ms Time-out detection multiplier: 3 BFD session 2 PW name: 3and1000pw Tx interval: 10 ms 16-97 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 254 ZXA10 C300 Configuration Manual (CLI) Item Data Rx interval: 10 ms Time-out detection multiplier: 3 Name: redundancy-vll PW: 2and1000pw Class map Name: classmap1000 SVLAN ID: 1000 Index: 1 Service type: ethernet class-map Class map: classmap1000 C300-2 Loopback interface ID ID: 1 IP address: 2.2.2.2/32...
Page 255 The data on a CIP is a certain service flow, which is specified by a class map, from a UNI. Configuration Flow Figure 16-29 shows the configuration flowchart of the PW redundancy and BFD. 16-99 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 256: Figure 16-29 Configuration Flowchart Of Pw Redundancy And Bfd
ZXA10 C300 Configuration Manual (CLI) Figure 16-29 Configuration Flowchart of PW Redundancy and BFD Steps Configuration on C300-1. 1. Configure the loopback interface. ZXAN(config)#interface loopback1 ZXAN(config-loopback1)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-loopback1)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1...
Page 257 8. Configure the PW class. ZXAN(config)#pw-class pw1 ZXAN(config-pw-class)#control-word not-preferred ZXAN(config-pw-class)#cctype type2 ZXAN(config-pw-class)#cvtype lsp-ping bfd-ipudp-fo ZXAN(config-pw-class)#exit 9. Configure the PWs. ZXAN(config)#pw 2and1000pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet ZXAN(config-pw)#apply pw-class pw1 ZXAN(config-pw)#peer 2.2.2.2 router-id 2.2.2.2 vcid 1000 ZXAN(config-pw)#exit 16-101 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 258 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#pw 3and1000pw ZXAN(config-pw)#mode dynamic pwe3 fec128 ZXAN(config-pw)#pwtype ethernet ZXAN(config-pw)#apply pw-class pw1 ZXAN(config-pw)#peer 3.3.3.3 router-id 3.3.3.3 vcid 1000 ZXAN(config-pw)#exit 10. Configure the PW redundancy group. ZXAN(config)#pw-redundancy-group 2and3vcid1000 ZXAN(config-pw-group)#negotiation disable ZXAN(config-pw-group)#protect-type 1by1 ZXAN(config-pw-group)#protect hold-off 0 ZXAN(config-pw-group)#protect mode revertive wtr 1...
Page 259 ZXAN(config-pw)#peer 1.1.1.1 router-id 1.1.1.1 vcid 1000 ZXAN(config-pw)#exit 10. Configure the BFD session. ZXAN(config)#mpls pw bfd 1and1000pw interval 10 min-rx 10 multiplier 3 11. Configure the VLL. ZXAN(config)#vll redundancy-vll ZXAN(config-vll)#mpls xconnect pw 1and1000pw ZXAN(config-vll)#exit 12. Configure the class map. 16-103 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 260 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#class-map classmap1000 ZXAN(config-cmap)#match svlan-id 1000 ZXAN(config-cmap)#exit 13. Configure the CIP. ZXAN(config)#cip 1 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect redundancy-vll ZXAN(config-cip1)#oam-mapping enable ldp ZXAN(config-cip1)#exit 14. Save the configuration data. Configuration on C300-3. 1. Configure the loopback interface.
Page 261 ZXAN(config-cip1)#service-type ethernet class-map classmap1000 ZXAN(config-cip1)#xconnect redundancy-vll ZXAN(config-cip1)#oam-mapping enable ldp ZXAN(config-cip1)#exit 12. Save the configuration data. Result When the primary PW is disabled, the secondary PW is activated, and the two CEs can ping each other successfully. 16-105 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 262 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 16-106 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 263: Ethernet Oam Configuration
Ethernet OAM Configuration..................17-1 BFD Configuration....................17-7 17.1 Ethernet OAM Configuration The ZXA10 C300 supports service layer OAM function, which includes link continuity check, port loopback detection, link trace, and alarm notification. 17.1.1 Configuring the CCM Function CCM is used to ensures the continuity between MPs in an MA.
Page 264 ZXA10 C300 Configuration Manual (CLI) Item Data Remote MEP Session ID: 2 MEP ID: 2 Remote MAC address: 00d0.d058.6958 Uplink interface gei_1/21/1 Note: The remote MAC address of the remote MEP is the in-band MAC address of the local MEP.
Page 265: Configuring The Lbm Function
– End of Steps – Result If the ZXA10 C300 receives error CCM packets or does not receive any CCM packets, there will be a CCM alarm information on the NMS. You can query the CCM alarm information using the show cfm mp all md 1 ma 1 detail command.
Page 266: Table 17-2 Configuration Data Of Lbm Function
ZXA10 C300 Configuration Manual (CLI) Table 17-2 Configuration Data of LBM Function Item Data Session ID: 1 Name: md1 Level: 3 Session ID: 1 Name: ma1 Protection mode: VLAN protection Primary VLAN ID: 100 Local MEP Session ID: 1 MEP ID: 1...
Page 267: Configuring The Ltm Function
When MPs on the path receive the LTM packets, each MP responds to the source MEP with an LTR message. When the destination is an MIP, the MIP does not forward the LTM anymore. 17-5 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 268 ZXA10 C300 Configuration Manual (CLI) Steps 1. Enable the function. ZXAN(config)#cfm enable 2. Create the Ethernet OAM MD. ZXAN(config)#cfm create md session 1 name md1 level 3 3. Create the Ethernet OAM MA. ZXAN(config-md1)#create ma session 1 format icc-based name ma1 4.
Page 269: Bfd Configuration
Figure 17-1 BFD Applications 17.2.1 Configuring the BFD for Static Routes BFD can be used to detect faults on static routes. Networking Diagram Figure 17-2 shows the networking diagram of the for static routes. 17-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 270: Figure 17-2 Networking Diagram Of Bfd For Static Routes
ZXA10 C300 Configuration Manual (CLI) Figure 17-2 Networking Diagram of BFD for Static Routes There are two static routes between C300-1 and C300-3. The active route is: C300-1 > C300-2 > C300-3. The backup route is: C300-1 > C300-4 > C300-3.
Page 271 ZXAN(config-if)#ip address 1.1.1.1 255.255.255.255 ZXAN(config-if)#exit 2. Configure the VLAN of the uplink interfaces. ZXAN(config)#interface gei_1/21/1 ZXAN(config-if)#switchport vlan 10 tag ZXAN(config-if)#exit ZXAN(config)#interface gei_1/21/2 ZXAN(config-if)#switchport vlan 13 tag ZXAN(config-if)#exit 3. Configure the IP address of the VLAN interfaces. 17-9 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 272 ZXA10 C300 Configuration Manual (CLI) ZXAN(config)#interface vlan 10 ZXAN(config-if-vlan10)#ip address 10.1.1.1 255.255.255.0 ZXAN(config-if-vlan10)#exit ZXAN(config)#interface vlan 13 ZXAN(config-if-vlan13)#ip address 13.1.1.2 255.255.255.0 ZXAN(config-if-vlan13)#exit 4. Configure the routes. ZXAN(config)#ip route 3.3.3.3 255.255.255.255 10.1.1.2 ZXAN(config)#ip route 3.3.3.3 255.255.255.255 13.1.1.1 200 slave tag 200 5. Configure the BFD.
Page 273: Configuring The Bfd For Vccv
ZXAN(config-if-vlan13)#exit 17.2.2 Configuring the BFD for VCCV BFD can be used for Virtual Circuit Connectivity Verification (VCCV) in MPLS network OAM. Networking Diagram Figure 17-3 shows the networking diagram of the for VCCV. 17-11 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 274: Figure 17-3 Networking Diagram Of Bfd For Vccv
ZXA10 C300 Configuration Manual (CLI) Figure 17-3 Networking Diagram of BFD for VCCV The PW redundancy group works in non-negotiation 1:1 mode. The primary PW is revertive when it recovers. BFD packets that notify PW alarms are encapsulated in VCCV mode (IP/UDP BFD encapsulation).
Page 275 C300-2 Loopback interface ID ID: 1 IP address: 2.2.2.2/32 L3 interface VLAN ID: 11 Interface: gei_1/21/1 IP address: 10.1.1.1/24 Reserved VPN VLAN VLAN ID: 4090 PW class Name: pw1 Control word: not preferred 17-13 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 276 ZXA10 C300 Configuration Manual (CLI) Item Data Control Channel (CC) type: type2 (out-of-band) Connection Verification (CV) type: lsp-ping bfd-ipudp-fo Name: 1and1000pw Mode: dynamic pwe3 PW class: pw1 Peer: 1.1.1.1 Router ID: 1.1.1.1 VC ID: 1000 BFD session PW name: 1and1000pw...
Page 277 For steps of configuring the BFD for VCCV, refer to Steps in 16.5.3 Configuring the PW Redundancy and BFD. Result Execute the commands ping mpls ipv4 2.2.2.2 32 repeat 10 and ping mpls pseudowire pw-n ame 2and1000pw on C300–1. These pings are successful. 17-15 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 278 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 17-16 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 279: Chapter 18 Route Protocol Configuration
Configuring the OSPF Protocol ................18-1 Configuring the BGP ....................18-2 18.1 Configuring the Static Route This section describes how to implement the static route of the ZXA10 C300 by configuring the next hop address to the destination network segment. Context Static route is the route info added into the routing table by the network administrator via the configuration command.
Page 280: Configuring The Bgp
2. Configure the network segment of the interface. ZXAN(config-router)#network 10.1.1.0 0.0.0.255 area 0 – End of Steps – 18.3 Configuring the BGP This section describes how to implement the ZXA10 C300's access to the adjacent router by configuring the BGP. Context is an inter-AS routing protocol.
Page 281: Chapter 19 Clock Configuration
Configuring the External Output Clock..............19-4 Configuring PTP Slave Clock ...................19-6 19.1 Configuring the Synchronous Ethernet Clock The ZXA10 C300 supports the synchronous Ethernet clock and can provide the synchronous Ethernet clock for the ONU via the PON port. Configuration Data Table 19-1 lists the configuration data of the synchronous Ethernet clock.
Page 282 ZXA10 C300 Configuration Manual (CLI) Item Data Clock type SYNCE Priority Clock value QL-SEC port 1/5/1 Steps 1. Query the current clock source. ZXAN(config)#show clock source active interface :1/10/0 type :internal ssm-ql :qlsec status :free_run warning :none operation :none 2. In clock configuration mode, configure the clock source.
Page 283: Configuring External Input Clock
– End of Steps – 19.2 Configuring External Input Clock The ZXA10 C300 supports the external input clock via the common interface card. Configuration Data Table 19-2 lists the configuration data of the external input clock. Table 19-2 Configuration Data of the External Input Clock...
Page 284: Configuring The External Output Clock
– End of Steps – 19.3 Configuring the External Output Clock The ZXA10 C300 supports the external output clock via the common interface card. Configuration Data Table 19-3 lists the configuration data of the external output clock. 19-4 SJ-20130520164529-007|2013-06-30 (R1.0)
Page 285 ZXAN(config-clock)#external-input 1/20/1 quality sec mode bits 4. Configure the SSM value of the clock source. ZXAN(config-clock)#ssm-set 1/20/1 qlsec 5. Configure the external output clock. ZXAN(config-clock)#external-output ssmThreshold sec mode bits 6. (Optional) Query the clock configuration. 19-5 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 286: Configuring Ptp Slave Clock
300 ms; QL-enable external-clock: unbalance – End of Steps – 19.4 Configuring PTP Slave Clock The ZXA10 C300 works as the slave clock to transmit PTP clock signals to downlink ONUs. Prerequisite A reliable PTP source clock exits in the network.
Page 287 -4 1970-01-01 00:35:02 n ptp configure count：1 6. (Optional) Query the PTP source configuration. ZXAN(config)#show time ptp-source addr adjust Layer2 ........ 192.168.2.1 time source count：1 – End of Steps – 19-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 288 ZXA10 C300 Configuration Manual (CLI) This page intentionally left blank. 19-8 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 289: Figures
Figure 16-16 Configuration Flowchart of VPWS ............ 16-50 Figure 16-17 PWE3 Network Reference Model............. 16-54 Figure 16-18 Networking Diagram of Basic PWE3 Service........16-55 Figure 16-19 Configuration Flowchart of PW Redundancy ........16-57 Figure 16-20 Networking Diagram of Multi-Segment PWs........16-61 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 290 ZXA10 C300 Configuration Manual (CLI) Figure 16-21 Configuration Flowchart of Multi-Segment PWs ....... 16-64 Figure 16-22 Networking Diagram of TDM Relay Service ........16-69 Figure 16-23 Configuration Flowchart of TDM Relay Service ........ 16-73 Figure 16-24 Networking Diagram of VPLS Redundancy ........16-78 Figure 16-25 Configuration Flowchart of VPLS Redundancy.........
Page 291 Table 5-1 VLAN Specifications .................. 5-1 Table 6-1 Configuration Data of the IGMP MVLAN............ 6-2 Table 6-2 Configuration Data of the MLD MVLAN ............. 6-5 Table 6-3 Configuration Data of the IPTV Package ........... 6-7 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 292 ZXA10 C300 Configuration Manual (CLI) Table 8-1 Configuration Data of the Standard ACL............ 8-2 Table 8-2 Configuration Data of the Extended ACL ........... 8-3 Table 8-3 Configuration Data of the Layer-2 ACL ............8-5 Table 8-4 Configuration Data of the Hybrid ACL............8-6 Table 8-5 Configuration Data of the IPv6 Hybrid ACL ..........
Page 293 Tables Table 19-2 Configuration Data of the External Input Clock ........19-3 Table 19-3 Configuration Data of the External Output Clock........19-5 Table 19-4 PTP Slave Clock Configuration Data ............. 19-6 SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 294 Tables This page intentionally left blank. SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 295: Glossary
- Broadband Remote Access Server - Channel Access Control - Continuity Check Message - Call Detail Record - Customer Edge - Circuit Emulation Service - Connectivity Fault Management - Customer Interface Point - Command Line Interface SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 296 ZXA10 C300 Configuration Manual (CLI) CVLAN - Customer Virtual Local Area Network - Class of Service DHCP - Dynamic Host Configuration Protocol - Domain Name System DSCP - Differentiated Services Code Point - Denial of Service EPON - Ethernet Passive Optical Network...
Page 297 - Loss Of Signal - Label Switched Path - Maintenance Association - Media Access Control - Maintenance Domain - Metro Ethernet Forum - MEG End Point - MAC-Forced Forwarding - Media Gateway Controller - MEG Intermediate Point SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 298 ZXA10 C300 Configuration Manual (CLI) - Multicast Listener Discovery MPLS - Multiprotocol Label Switching MS-AIS - Multiplex Section - Alarm Indication Signal - Multiple Spanning Tree MSTP - Multiple Spanning Tree Protocol MVLAN - Multicast Virtual Local Area Network - Neighbor Discovery Protocol...
Page 299 - Synchronous Digital Hierarchy - SDH Equipment Clock - Session Initiation Protocol - Subscription-Notification-Answer SONET - Synchronous Optical Network - Secure Shell - Synchronization Status Message SSTP - Single Spanning Tree Protocol - Spanning Tree Protocol SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...
Page 300 ZXA10 C300 Configuration Manual (CLI) SVLAN - Service Virtual Local Area Network TACACS+ - Terminal Access Controller Access-Control System Plus - Transmission Control Protocol - Time Division Multiplexing - Terminal Identification - Transparent LAN Service - Timing Marker - Type of Service...
Page 301 Glossary VoIP - Voice over Internet Protocol XIII SJ-20130520164529-007|2013-06-30 (R1.0) ZTE Proprietary and Confidential...

Zte ZXA10 C300 Configuration Manual

Chapter 1 Basic Configuration

Chapter 2 GPON/XG-PON Service Configuration

Chapter 3 CES Service Configuration

Chapter 4 P2P Service Configuration

Chapter 5 VLAN Configuration

Chapter 6 IPTV Configuration

Chapter 7 Qos Configuration

Chapter 8 ACL Configuration

Chapter 9 NTP Configuration

Chapter 10 STP Configuration

Chapter 11 DHCP Configuration

Chapter 12 Uplink Protection Configuration

Chapter 13 PON Protection Configuration

Chapter 14 Access Security Configuration

Chapter 15 System Security Configuration

Chapter 16 MPLS Service Configuration

Chapter 17 OAM Configuration

Chapter 18 Route Protocol Configuration

Chapter 19 Clock Configuration

Quick Links

Related Manuals for Zte ZXA10 C300

Summary of Contents for Zte ZXA10 C300