Transmitter Test; Transmitter Programming - Honda S2000 Service Manual

Keyless/Power Door Locks
Transmitter Test
NOTE:
. lf the doors unlock or lock with the transmitter, but
the LED on the transmitter does not come on, the LED
is faulty; replace the transmitter.
. l f a n y d o o r i s o p e n , y o u c a n n o t l o c k t h e d o o r w i t h t h e
transmitter.
. lf you unlocked the doors with thetransmitter, but do
not open any of the doors within 30 seconds, the
doors relock automatically.
. The doors do not lock or unlock with the transmitter if
the ignition key is inserted in the ignition switch.
1. Press the lock or unlock button five or six times to
reset the transmitter.
. lf the locks work, the transmitter is OK.l
. lf the locks don'twork, goto step 2.
2. Open the transmitter and check for water damage.
. l f y o u f i n d a n y w a t e r d a m a g e , r e p l a c e t h e
transmitter.l
. l f t h e r e i s n o w a t e r d a m a g e , g o t o s t e p 3 .
3. Replace the transmitter battery (A)with a new one,
and try to lock and unlock the doors with the
transmifter by pressing the lock or unlock button
five or six times.
. lf the doors lock and unlock, thetransmitter is
oK. a
. l f t h e d o o r s d o n ' t l o c k a n d u n l o c k , g o t o s t e p 4 .
Reprogram the transmifter, then try to lock and
unlock the doors.
. lf the doors lock and unlock, the transminer is
oK. t
. lf the doors don't lock and unlock, replace the
transmitter.l
22-138
Transmitter Programming
Storing transmitter codes: The codes of up to three
transmitters can be programmed into the keyless
receiver unit memory. (lf a fourth code is stored, the
code which was input first will be erased.)
N O T E : l t i s i m p o r t a n t t o m a i n t a i n t h e t i m e l i m i t s
kretween the steps. Make sure the doors, the hood and
the trunk are closed.
1 , T u r n t h e i g n i t i o n s w i t c h O N ( l l ) .
2. Within 1 to 4 sec., push the transmitter lock or
unlock button with the transmitter aimed at the
receiver unit behind the driver's side dash.
3, Within 1 to 4 sec., turn the ignition switch OFF.
4. Within 1 to 4 sec., turn the ignition switch ON (ll).
5. Within 1 to 4 sec., push the transmitter lock or
unlock button with the transmitter aimed at the
receiver unit behind the driver's side dash.
6. Within 1 to 4 sec., turn the ignition switch OFF.
7. Within 4 sec., turn the ignition switch ON (ll).
8. Within 1 to 4 sec., push the transmitter lock or
unlock button with the transmitter aimed at the
receiver unit behind the driver's side dash.
9. Within I to 4 sec., turn the ignition switch OFF.
1 0 . W i t h i n 4 s e c . . t u r n t h e i g n i t i o n s w i t c h O N ( l l ) ,
1 1. Within 1 to 4 sec., push the transmitter lock or
unlock button with the transmitter aimed at the
receiver unit behind the driver's side dash.
Confirm you can hear the sound of the door lock
actuators. Within
'l to 4 sec., push the transmitter
lock or unlock button again. The keyless receiver
unit is now in the program mode. You must push
the transmitter lock or unlock button of the first
transmitter again to program that remote.
Within 10 sec., aim the transmitters (up to two
additional ones) whose codes you want to store at
the receiver unit, and Dress the transmitter lock or
unlock buttons.
Confirm that you can hear the sound of the door
lock actuators after each transmitter code is stored.
1 4 . T u r n t h e i g n i t i o n s w i t c h O F F , a n d p u l l o u t t h e k e y ,
15. Confirm proper operation of the transmitters with
the new code{s).
1 2 .