Xerox ColorQube 9303 Series Service Manual page 1423

Table 2 IIT DADH NVM ID 800-xxx
NVM ID NVM Name NVM Description
801-014 Scan LE Hotline Scan LE hot line
801-015 Mono Set Point Mono set point
801-016 Red Set Point Red set point
801-017 Green Set Point Green set point
801-018 Blue Set Point Blue set point
801-019 ReCalMag200 ReCalMag200
801-020 CvtMonoAgcAd- CvtMonoAgcAdjus
just
801-021 CvtRedAgcAdjust CvtRedAgcAdjus
801-022 CvtGrnAgcAdjust CvtGrnAgcAdjus
801-023 CvtBlueAgcAdjust CvtBlueAgcAdjus
ColorQube® 9303 Family
Settings Default
0.1 mm increments 280
Range = 100 to 900
Grey Level in whole number 198
Range = 170 to 255
Grey Level in whole number 191
Range = 170 to 255
Grey Level in whole number 197
Range = 170 to 255
Grey Level in whole number 205
Range = 170 to 255
0 = Never 1
1 = Re-calibrate for non-
mixed originals
2 = Always Calibrate
Range = 0 to 2
% whole numbers. 100 cor- 103
responds to no DADH offset
compensation. Setting
greater than 100 compen-
sates for DADH darker than
platen.
Range = 80 to 120
% whole numbers. 100 cor- 104
responds to no DADH offset
compensation. Setting
greater than 100 compen-
sates for DADH darker than
platen.
Range = 80 to 120
% whole numbers. 100 cor- 104
responds to no DADH offset
compensation. Setting
greater than 100 compen-
sates for DADH darker than
platen.
Range = 80 to 120
Tenths of %. 1000 (100%) 103
corresponds to no DADH
offset compensation. Setting
greater than 1000 compen-
sate for DADH darker than
platen.
Range = 80 to 120
February 2013
6-131
Table 2 IIT DADH NVM ID 800-xxx
NVM ID NVM Name NVM Description
801-024 Speed Mode Speed mode
801-025 Scanner Type Scanner type, full width
array or charged cou-
pled device
801-026 IQ Parameter IQ parameter version
Version
801-027 DADH / Platen DADH / platen configu-
Configuration ration
Table 3 IOT NVM (IME) ID Range 400 to 439-xxx
NVM ID NVM Name NVM Description
410-001 Transfix calibra- Transfix front load calibration
tion front factor
410-002 Transfix calibra- Transfix rear load calibration
tion rear factor
410-003 Transfix cal Invalidate transfix calibration
invalid
410-004 Transfix Load for Transfix load value for large
Large Envelope envelopes
420-001 Ink Level Cyan Track ink mass - cyan
420-002 Ink Level Track ink mass - magenta
Magenta
420-003 Ink Level Yellow Track ink mass - yellow
Settings Default
0 = 257 mm/s 0
1 = 234 mm/s
2 = 234 mm/s
Range = 0 to 3
1 = FWA 1
2 = CCDS
Range = 0 to 255
Holds the scan parameter 1
version index and distin-
guishes between minor vari-
ations within a scanner
family, e.g. filter change,
lens change. Set to 1 for
ColorQube at launch.
Range = 0 to 255
0 = DADH / Platen present 1
1 = Platen only
Range = 0 to 1
Settings Default
Range = -1,500 to 2,200
3,500
Range = -1,500 to 2,200
3,500
Range = 0 to 1 1
Range = 2,000 to 2,000
5,100
(+) when sticks 0
added
(-) when pixels print
Range = 0 to
4,294,967,295
(+) when sticks 0
added
(-) when pixels print
Range = 0 to
4,294,967,295
(+) when sticks 0
added
(-) when pixels print
Range = 0 to
4,294,967,295
General Procedures/Information
dC131