Table of Contents
Advertisement
dC967 Head to Drum Spacing Check
Purpose
To check the head to drum spacing. The procedure checks for contact between each printhead
and the drum.
This check will run automatically if a new printhead serial number is detected during power-up.
The dc967 window will not be present, but a status message will reflect this check is taking
place.
If a printhead is reinstalled (not replaced) in the same position on a carriage, the machine will
not recognize it as new during power-up, and this check will not automatically occur. To prevent
carriages from automatically docking during power-up, boot the machine directly into IME
Diagnostics Mode,
GP 1
and then proceed to step 1 anytime a printhead has been reinstalled.
Procedure
The procedure normally takes approximately 7 - 10 minutes to run and cannot be stopped once
in operation.
NOTE: The dC967 routine will stop if potential printhead to drum contact is detected. If poten-
tial printhead to drum contact is identified, perform
Perform the following:
1.
Boot the machine directly into IME Diagnostics Mode,
2.
Select the Diagnostics tab.
3.
Select dC967 Head to Drum Spacing Check.
4.
Select Start. The following sequence of events are controlled by the IME:
•
The IME brings the printhead and drum to operating temperature.
•
The drum is stopped.
•
Both the upper and lower carriage assemblies are placed into the docked position.
•
The upper carriage assembly is parked while the lower carriage is docked and the
process is reversed.
•
Once the temperature measurements are complete, the IME will move the carriage
assemblies into the parked position.
•
Results are reported:
–
Passed.
–
Head to Drum Spacing Check Failed.
5.
Select Start to repeat the process or Close to exit the procedure.
6.
Select Close to return to the service mode window.
7.
Select Call Closeout to exit service mode.
General Procedures/Information
dC967, dC968
ADJ 91.1
Printhead Attachment Check.
GP
1.
February 2013
dC968 Head Purge
Purpose
To force ink through all jets on the selected printheads.
Initial Actions
Before running this routine check the following:
•
Sufficient ink must be available for each colour.
•
The waste tray must not be full.
•
A4 or letter size paper should be loaded.
•
The IME is ready to print.
NOTE: All test prints should be printed long edge feed.
Procedure
1.
Enter service mode,
GP
1.
2.
Select the Maintenance tab.
3.
Select dC968 Head Purge.
The dC968 Head Purge window opens. Follow the on screen instructions.
NOTE: The main head purge screen has 3 selectable routines:
•
Jet test pages
(TP
21)
•
Cleaning pages
(TP
22)
•
Purge head routine
4.
Select Jet Test Pages. The machine will run the jet test routine which will print 2 pages for
each colour.
NOTE: Before printing the jet test page, ensure that A4 or 8.5 x11 inch plain paper is
loaded LEF into tray 4. Use the best quality media available. Do not use hole punched
paper.
5.
Use the jet test pages to identify any defective heads. Refer to
interpret the jet test output.
Empty the waste tray before purging the heads. When the waste tray has been emptied touch
the Reset Waste Counter button.
6.
Select head 1, 2, 3 or 4 from the Purge Heads buttons and touch the Purge button to start
the purge routine.
NOTE: The Head Purge routine takes from 4 to 8 minutes depending on the number of
heads selected.
When the heads have finished purging the machine will run a cleaning page for the
purged heads. Depending on the number of heads purged the machine will print 1 or 2
cleaning pages with 2 heads cleaned on each page.
7.
Select Jet Test Pages.
The machine will run the jet test routine which will print 2 pages for each colour.
8.
Inspect the Jet Test Pages. If a defect is found repeat the procedure.
9.
Select Close to return to the maintenance window.
10. Select Call Closeout.
6-290
TP 21
Jet Test Pages to
CAUTION
ColorQube® 9303 Family
Advertisement
Chapters
Table of Contents
