Xerox ColorQube 9303 Series Service Manual page 1436

Table 6 IOT NVM (IME) ID Range 489 to 499-xxx
NVM ID NVM Name NVM Description
490-048 A correction offset Stitch Measure Offset Y2 Rear Range = -1000 to
value applied to Y
stitch rear mea-
surements for
stitch interface 2.
490-049 A correction offset Stitch Measure Offset Y3 Rear Range = -1000 to
value applied to Y
stitch rear mea-
surements for
stitch interface 3.
490-050 TMP:H1Fix Jets TMP = too many purges fea-
Purge Needed ture
TMP: count of semi-consecui-
tive nights in which head 1
sees purge needed to fix jets.
490-051 TMP:H2Fix Jets TMP: count of semi-consecui-
Purge Needed tive nights in which head 2
sees purge needed to fix jets.
490-052 TMP:H3Fix Jets TMP: count of semi-consecui-
Purge Needed tive nights in which head 3
sees purge needed to fix jets.
490-053 TMP:H4Fix Jets TMP: count of semi-consecui-
Purge Needed tive nights in which head 4
sees purge needed to fix jets.
490-054 TMP:H1Fix Jets TMP: count of semi-consecui-
Prg NOT Needed tive nights in which head 1
sees purge NOT needed to fix
jets.
490-055 TMP:H2Fix Jets TMP: count of semi-consecui-
Prg NOT Needed tive nights in which head 2
sees purge NOT needed to fix
jets.
490-056 TMP:H3Fix Jets TMP: count of semi-consecui-
Prg NOT Needed tive nights in which head 3
sees purge NOT needed to fix
jets.
490-057 TMP:H4Fix Jets TMP: count of semi-consecui-
Prg NOT Needed tive nights in which head 4
sees purge NOT needed to fix
jets.
General Procedures/Information
dC131
Settings Default NVM ID
0 490-058 TMP:Max Fix Jets
1000
0
1000
490-059 TMP:Max Fix Jets
Range = 0 to 255 0
490-060 Unif-CLD Base-
Range = 0 to 255 0
Range = 0 to 255 0
Range = 0 to 255 0
490-061 Unif-CLD Base-
Range = 0 to 255 0
490-062 Unif-CLD Base-
Range = 0 to 255 0
490-063 Wait GelMaint
490-064 Override Unifor-
Range = 0 to 255 0
490-065 Delta CU-PC
Range = 0 to 255 0
February 2013
6-144
Table 6 IOT NVM (IME) ID Range 489 to 499-xxx
NVM Name NVM Description
TMP: A threshold of purge
Purge Needed maintenance sessions that
had purges to correct bad jets.
If this threshold is exceeded a
Head x Too Many Purges infor-
mational fault is raised and the
heads jet fix purging is
blocked.
TMP: When the number of
Prg NOT Needed purge maintenance sessions
which requires no purges to fix
bad jets exceeds this value the
Head x Too Many Purges Dev-
Fault is lowered
CLD = CloseLoopDrift = a new
line Status way to achieve uniformity via
IOD. CLD baseline (via IOD) is
a new calibration required by
uniformity (CLDAdjust). This is
PQM status for CLD baseline.
PQM consecutive failure count
line Failure for CLD baseline
What is the youngest heads
line Last Success time at temp when CLD base-
line last succeeded
Min CU print count before
until CU-PC PQM begins running automatic
CU Gel Maintenance at night.
Switch to go back to old unifor-
mity Algorithm mity algorithm vs new closed
loop drift algorithm.
Min CU print count between
between Gel- automatic CU Gel mainte-
Maint nances at night
Settings Default
Range = 0 to 255 16
Range = 0 to 255 2
Range = 0 to 255 0
Range = 0 to 4 1
Range = 0 to 0
4,294,967,295
Range = 0 to 25,000
4,294,967,295
0 = New CLD unifor- 0
mity
1 = Old uniformity
Range = 0 to 225
Range = 0 to 5,000
4,294,967,295
ColorQube® 9303 Family