Table of Contents
Advertisement
61202800L1-1B
IQ 710
Section 4, User Interface Guide
Page 46
S
C
-
TART
HANNEL
with the carrier if using a public network. The range is
N
C
UMBER OF
HANNELS
Enabling performance report messages (PRM) allows the IQ 710 to send messages
T
PRM -
RANSMIT
across the facility data link (FDL) per ANSI T1.403. The terminating device at the telco may use this
information for management of the T1 loop.The IQ 710 supports PRM messages per AT&T Pub
54016 which is a poll/response type protocol. Because of this poll/response nature, the transmit PRM
option does not disable the IQ 710 from processing or responding to 54016-type messages.
Choices:
or
Y
N
ES
O
C
>N
ONFIGURATION
ETWORK
I
M
NTERFACE
ODULE
Set the loop rate for
L
R
-
OOP
ATE
Configure the IQ 710 to derive clocking from itself (
C
S
-
LOCK
OURCE
The most common application is
C
>N
ONFIGURATION
ETWORK
Set the signaling type option to match the network signaling type. A
same signaling type as the attached frame relay DTE. If A
attached, the IQ 710 uses ANSI T1.617-D signaling type.
Choices: N
, LMI (gang of four), ANSI T1.617-D (Annex D), ITU-T Q.933-A (Annex A), or A
ONE
C
>N
ONFIGURATION
ETWORK
Set the signal polls to either
signal state of the network. If set to
device.
C
>N
ONFIGURATION
ETWORK
Set the time (in seconds) between polls to the frame relay network.
C
>N
ONFIGURATION
ETWORK
Determine how many link integrity polls occur in between full status polls.
C
>N
ONFIGURATION
ETWORK
These parameters define the error threshold for the UNI formed by the IQ 710 network port and the frame
relay switch. If the error threshold is met, the signaling state is changed to down, which indicates a
service-affecting condition. This condition is cleared once N393 consecutive error-free events are
received. N392 defines the number of errors required in a given event window, while N393 defines the
number of polling events in each window.
IQ 710 System Manual
Select the channel in which the T1 stream starts. The setting must be consistent
Select the number of DS0s (channels) to be used. The range is
-
.
P
>P
ORT
HYSICAL
56
KBPS
F
N
ROM
ETWORK
P
>F
ORT
RAME
P
>F
ORT
RAME
or
N
F
ORMAL
OLLOWS
F
DTE
OLLOWS
P
>F
ORT
RAME
P
>F
ORT
RAME
P
>F
ORT
RAME
.
1-24
L
O
AYER
PTIONS
or
.
, 64
,
KBPS
AUTO
.
R
O
>S
ELAY
PTIONS
UTO
is selected and there is no DTE device
UTO
R
O
>S
ELAY
PTIONS
. If set to
DTE
N
ORMAL
, the signal state will reflect the signal state of the DTE
R
O
>T391
ELAY
PTIONS
R
O
>N391
ELAY
PTIONS
R
O
>N392
ELAY
PTIONS
1-24
>56/64K N
ETWORK
) or from the network.
I
NTERNAL
T
IGNAL
YPE
mode forces the IQ 710 to use the
P
IGNAL
OLLS
, the signal state will reflect the
N393
AND
© 2002 ADTRAN, Inc.
.
.
UTO
Advertisement
Chapters
Table of Contents
