Emerson Micro Motion 2700 Configuration And Use Manual page 160

Model 2700 PROFIBUS Block Parameters
Table F-2 Physical block parameters (continued)
Index Parameter Mnemonic
20 ALERT_KEY
21 TARGET_MODE
22 MODE_BLK
23 ALARM_SUM
Physical block parameters
24 SOFTWARE_REVISION
(DD Name: Software Revision)
25 HARDWARE_REVISION
(DD Name: Hardware
Revision)
26 DEVICE_MAN_ID
(DD Name: Manufacturing ID)
27 DEVICE_ID (DD Name: Device
ID)
28 DEVICE_SER_NUM
(DD Name: PB Serial Number)
29 DIAGNOSIS(DD Name:
Physical Block Diagnosis)
30 EMPTY
31 DIAGNOSIS_MASK(DD
Name: Diagnosis Mask)
32 EMPTY
33 EMPTY
34 EMPTY
35 EMPTY
36 Reserved
37 Reserved
38 DEVICE_INSTALL_DATE
40 IDENT_NUMBER_
SELECTOR
(DD Name: Ident Number)
42 FEATURE
(DD Name: phys Feature)
152
Definition
This parameter contains the
identification number of the plant
unit.
This parameter contains desired
mode normally set by a control
application of an operator. The
modes are valid alternatively only,
i.e. only one mode can be set at
one time. A write access to this
parameter with more than one
mode is out of the range of the
parameter and has to be rejected.
This parameter contains the
current mode and the permitted
and normal mode of the block.
This parameter contains the
current states of the block alarms.
Revision-number of the software
of the field device.
Revision-number of the hardware
of the field device.
Identification code of the
manufacturer of the field device.
Manufacturer specific identification
of the device.
Serial number of the field device.
Detailed information of the device,
bitwise coded. More than one
message
possible at once. If MSB of byte 4
is set to 1 than more diagnose
information is
available in the
DIAGNOSIS_EXTENSION
parameter.
Definition of supported
DIAGNOSIS information-bits.
Device Installation Date
Each PROFIBUS-DP /IEC 61158/
device shall have an
Ident_Number provided by
the PNO. There are profile specific
Ident_Numbers. A device may
have profile
specific and manufacturer specific
ones. The user is able to choose
one of these
using this parameters.
Indicates optional features
implemented in the device and the
status of these
Features which indicates if the
feature is supported or not
supported.
Message Data Type/ Size
Type Structure
SIMPLE Unsigned8 1
SIMPLE Unsigned8 1
RECORD DS-37 3
RECORD DS-42 8
Simple Visible String 16
Simple Visible 16
String
Simple Unsigned16 2
Simple Visible String 16
Simple Visible String 16
Simple Octet String 4
byte4,MSB=1
more diag
available
Simple Octet string 4
Simple Octect String 16
Simple Unsigned8 1
Record DS-68 8
Store Default Access Enumerated List of
/Rate Value Values / Range
(HZ)
S 0 R/W NA
S AUTO R/W AUTO ( 0x08)
(0x08)
D --- R NA
D 0,0,0,0 R NA
Cst --- R NA
Cst 1.0 R NA
Cst ---- R NA
Cst ---- R NA
Cst ---- R NA
D ---- R Refer byte 11 to 14
of Extended
Diagnostics bytes
in Appendix A
Cst ---- R Out of Mandatory
Alarms out of 4
Octets only Ident
No. violation Alarm
is supported.
And Extension
Available Alarm is
supported
0: not supported
1: supported
S Blank R/W
S ---- R/W 0: profile specific
Ident_Number
V3.01 (mandatory)
1: manufacturer
specific
Ident_Number
V3.01
N 0x03, R PROFIBUS
0x00, Specification
0x00, June 2005
0x00, Order No: 3.042
0x02, Amendment 2
0x00, to
0x00, the Profibus Profile
0x00 for Process
Control Devices V
3.01
Condensed Status
and Diagnostic
Messages
V 1.0
Model 2700 Transmitter with PROFIBUS-PA
Modbus
Register /
Coil
NA
NA
NA
NA
R-1200
Hard Coded
R-121
2545-2554
R122-123
NA
Hard Coded
0x00
0x80
0x00
0x80
2278-2285
NA
NA