Table of Contents
Advertisement
When drop border or shadow is selected: The
setting parameter values depend on the on/off
setting of key drop and the selection of 4H mode/
8H mode (see page 125).
• "Key drop off" mode
Knob Parameter Adjustment
1
Width
Width
2
Position
Position
3
Density
Density
• "Key drop on" mode
Knob Parameter Adjustment
1
Width
Width
2
Position
Position
3
Density
Density
a) In the "4H mode" and when [Fine Key] (page 135) is on, the setting
value range is 0.00 to 4.00.
When emboss is selected:
Knob Parameter Adjustment
1
Width
Width
2
Position
Position
a)
Density
3
Density
a) The Density adjustment only affects the key edge. This can be
adjusted separately from Key Density, and if Key Density is set to
0.00, the embossed edge effect only can be applied.
To make edge fill adjustments, carry out the settings in
step 6.
4
Select the edge fill signal in the <Edge Fill> group.
Utility 1 Bus: signal selected on the utility 1 bus
Matte: signal from dedicated color matte generator.
It becomes possible to adjust color 1.
Knob Parameter Adjustment
1
Luminance Luminance
2
Saturation
Saturation
3
Hue
Hue
When the edge type is outline, in place of the edge fill
signal, the selected key fill signal fills the outline, and
elsewhere remains as the background.
5
Carry out the following operation, depending on the
selection in step 4.
When [Utility 1 Bus] is selected: Hold down the
[UTIL] button in the cross-point control block,
and select the signal in the background A bus row.
While the [UTIL] button is held down, the
background A bus changes to the utility 1 bus.
Setting values
When [Matte] is selected: Press [Matte Adjust] in the
a)
0.00 to 8.00
359.99 to
180.00
0.00 to 100.00
Setting values
For the color mix operation, see "Carrying out a color
a)
0.00 to 8.00
mix for the key edge fill matte" (page 136).
359.99 to 0.00
6
When emboss is selected for the edge type, adjust the
0.00 to 100.00
To adjust matte 1 press [Matte1], and to adjust matte 2
press [Matte2], then adjust the following parameters.
Knob Parameter Adjustment
Setting values
1
0.00 to 4.00
2
359.99 to 0.00
3
0.00 to 100.00
7
To make the edge soft, press [Soft Edge] to set it on,
and adjust the softness.
Knob Parameter Adjustment
1
For a normal edge, when [Soft Edge] is enabled, [Key
Drop] is kept on.
8
To make separate fine adjustments to the positions of
the left, right, top, and bottom of the source edge, press
[Fine Key], to set it on, and adjust the following
Setting values
parameters.
0.00 to 100.00
0.00 to 100.00
359.99 to 0.00
Knob Parameter Adjustment
1
2
3
4
Notes
To enable the [UTIL] button, its operation mode
must be set to [Hold] beforehand.
For details, see "Setting the Button Operation
Mode" in Chapter 19 (Volume 2).
same EDGE menu, to display the Matte Adjust
menu, and adjust a single color or two-color
combination color matte.
You can select whether to use a single color matte
or a two-color combination color matte in the
<Edge Matte> group.
Luminance Luminance
Saturation
Saturation
Hue
Hue
Soft
Edge softness
Parameter group [1/2]
Top
Key top edge
position
Left
Key left edge
position
Right
Key right edge
position
Bottom
Key bottom
edge position
Setting values
0.00 to 100.00
0.00 to 100.00
359.99 to 0.00
Setting values
0.00 to 100.00
Setting values
–2.00 to +2.00
–2.00 to +2.00
–2.00 to +2.00
–2.00 to +2.00
135
Key Adjustments (Menus)
Advertisement
Table of Contents
