Table of Contents
Advertisement
To change the background only: Press one of the
[MIX], [NAM], [WIPE], and [DME] buttons.
The [KEY1] and [KEY2] buttons go off, and the
system changes to the background transition
mode.
To insert or delete key 1: Hold down the [KEY1]
button and press one of the [MIX], [NAM],
[WIPE], and [DME] buttons.
To insert or delete key 2: Hold down the [KEY2]
button and press one of the [MIX], [NAM],
[WIPE], and [DME] buttons.
To insert or delete key 1 and key 2 simultaneously:
Hold down the [KEY1] and [KEY2] buttons, and
press one of the [MIX], [NAM], [WIPE], and
[DME] buttons.
To use a super mix or preset color mix: Select
[Super Mix] or [Preset Color Mix] in the Misc
>Transition menu for the M/E or PGM/PST bank.
To set the key priority, use the Misc >Key Priority
menu for the M/E or PGM/PST bank (see page 100).
Notes
The transition type selection buttons ([MIX], [NAM],
[WIPE], and [DME]) can be assigned to other
transition types in setup.
For details, see "Setting Transition Control Block
Button Assignments" in Chapter 19 (Volume 2).
3
Select the new background for after the transition.
• Select the background video with the background B
row of cross-point buttons.
• To insert a key, select the key signal, and make
various settings as required.
For details of key settings, see Chapter 4 "Keys" (page
123).
4
Depending on the transition type selected in step 2,
make the required settings.
For details of the settings, see the following sections:
Super mix: "Super Mix Settings" (page 102)
Preset color mix: "Color Matte Settings" (page 103)
Wipe: "Basic Procedure for Wipe Settings" (page
163)
DME Wipe: "Basic Procedure for DME Wipe
Settings" (page 187)
Clip transition: "Clip Transition Operations" (page
219)
5
Carry out the transition in the transition execution
section.
For a gradual transition such as a mix or wipe:
Press the [TAKE] button, or operate the fader
lever.
See "Setting the Transition Rate" (page 105) and
"Pattern Limit" (page 107) as required.
Display of the Key Output Status and
Key Priority
You can check the output status of keys 1 and 2 and the key
priority setting, in the key status display in the transition
control block.
The key status display includes two ON indicators
corresponding to keys 1 and 2.
Display of the key output status
When the key is inserted in the output from the M/E or
not inserted, the indication goes off.
Key priority display
The key lying in front on the program monitor has an
indication "OVER" lit.
To set the key priority, use the Misc >Key Priority menu
for the M/E or PGM/PST bank (see page 100).
Split Fader
What does "split fader" mean?
The term "split fader" refers to the function of carrying out
a transition with the fader lever split into left and right
halves, so that the background A and background B buses
can be manipulated separately.
To use the split fader, the following conditions must be
met.
• The fader lever is in bus fixed mode.
For details, see "Selecting the Bank to Make the
Settings" in Chapter 20 (Volume 2).
• The necessary settings have been made in a Setup menu
to enable the split fader.
For details, see "Selecting the Bank to Make the
Settings" in Chapter 20 (Volume 2).
• A background is selected for the next transition.
• For the transition type, [MIX] or [NAM] is selected.
Split fader operation
The two halves of the split fader lever correspond to the
buses as follows.
Right fader lever: Background A bus
Left fader lever: Background B bus
The relationship between the positions of the two fader
levers and the image output in a mix is as follows.
Left lever
Right lever
position
position
Top
Top
Bottom
Top
Top
Bottom
A bus
B bus
output
output
100%
0%
100%
100%
0%
0%
Simple Transition
121
Advertisement
Table of Contents
