Motorola MPC8260 PowerQUICC II User Manual page 839

Part IV. Communications Processor Module
Table 29-27. ABR-Specific TCTE Field Descriptions (Continued)
Offset Bits Name
4Ð6 Ñ
7 CP-TA
8Ð9 Ñ
10 CI-VC
11Ð15 Ñ
0x08 Ñ MCR
0x0A Ñ UNACK Used by the CP to count F-RM cells sent in an absence of received B-RM cells. Initialize to
0x0C Ñ ACR
0x0E 0 ACRC
1Ð15 Ñ
0x10 Ñ RCTS
0x14 0 FRST
1Ð3 Ñ
4Ð7 CDF
8Ð15 COUNT Count. Used only by the CP. Holds the number of cells sent since the last forward RM cell.
0x16 Ñ ICR
0x18 Ñ CRM
0x1A Ñ ADTF
0x1C Ñ ER
0x1E Ñ ER-BRM Explicit rate-backward RM cell. Holds the maximum explicit rate value (in cells/sec)
29-59
Reserved, should be cleared.
Cell loss priorityÐturn-around cell. Holds the CLP of the last received F-RM cell. If another
F-RM cell arrives before the previous one was turned around, CP-TA is overwritten by the
new RM cellÕs CLP.
Reserved, should be cleared.
Congestion indication -VC. Holds the EFCI (explicit forward congestion indication) of the
last user data cell. The CI bit of the turned around RM cell is ORed with the CI-VC.
Initialize to 0.
Reserved, should be cleared.
Minimum cell rate Holds the minimum number of cells/sec of the current ABR channel.
Uses the ATMF TM 4.0 ßoating-point format.
0.
Allowed cell rate The cells per second allowed for the current ABR channel. Uses the
ATMF TM 4.0 ßoating-point format. Initialize with ICR.
ACR change. Indicates a change in ACR. Initialize to one.
Reserved, should be cleared.
RM cell time stamp. Used exclusively by the CP. Initialize to zero.
First turn. Used exclusively by the CP. Indicates the Þrst turn of a backward RM cell, which
has priority over a data cell. Initialized to 0.
Reserved, should be cleared.
Cutoff decrease factor. Controls the decrease in the ACR associated with missing B-RM
cells feedback. CDF represents a negative exponent of two, that is, the cutoff decrease
-CDF
factor = 2 . The cutoff decrease factor ranges from 1/64 (CDF=0b0110) to 1
(CDF=0b0000). All other CDF values falling outside this range are invalid.
Initialize with Nrm (in the parameter RAM).
Initial cell rate. The number of cells per second of the current ABR channel. The channelÕs
ACR is initialized with ICR. ICR uses the ATMF TM 4.0 ßoating-point format.
Missing RM cells count. Limits the number of forward RM cells that may be sent in the
absence of received backward RM cell. The CRM is in units of cells.
ADTFÐACR decrease time factor. The ADTF period is 500 ms as deÞned in the TM 4.0.
The ADTF value is deÞned by the system clock and the time stamp timer prescaler; see
Section 13.3.7, ÒRISC Time-Stamp Control Register (RTSCR).Ó For a time stamp prescaler
of 1 µs, ADTF should be programmed to 500m/(1µs ´ 1024)= 488.
Explicit rate. Holds the explicit rate value (in cells/sec) of the current ABR channel. ER is
copied to the F-RM cell ER Þeld. The user usually initializes this Þeld to PCR. ER uses the
ATMF TM 4.0 ßoating-point format.
allowed for B-RM cells. The ER-TA Þeld which is inserted to each B-RM cell is limited by
this value. ER-BRM uses the ATMF TM 4.0 ßoating-point format.
MPC8260 PowerQUICC II UserÕs Manual
Description
MOTOROLA