Extron electronics HDXP Plus Series User Manual page 69

Command
IP Setup Commands (continued)
Set DHCP on or off
Read DHCP status
Set IP address
Read IP address
Read hardware (MAC)
address
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set administrator password
Read administrator password
Reset (clear) administrator
password
Set user password
NOTE: An administrator password must be in place before a user password can be set.
Read user password
Reset (clear) user password
Bidirectional Serial Port Commands
Configure port parameters
24
Read port parameters
Set serial port mode
Read serial port mode
X2&
NOTE: = IP address
X3)
= Password
X3$
= MAC address
X4%
= DHCP status
X4^
= Serial port number
X4&
= Baud rate
X4*
= Parity
X4(
= Data bits
X5)
= Stop bits
X5!
= Serial port type
X5*
= Subnet mask
X5(
= Gateway IP address
ASCII Command
(Host to Switcher)
E X4% }
DH
E }
DH
E X2& }
CI CI
E }
CI
E }
CH
E X5* }
CS
E }
CS
E X5( }
CG
E }
CG
E X3) }
CA
E }
CA
E }
• CA
E X3) }
CU
E }
CU
E }
• CU
E X4^ X4& X4* X4( X5)
* , , CP
E X4^ }
CP
E X4^ X5! }
* CY
E X4^ }
CY
Format nnn.nnn.nnn.nnn. Leading zeros in each field are optional.
Administrator or user password can be 4 to 12 alphanumeric
characters. Spaces and special characters or symbols are not
allowed. The password is case-sensitive.
Format nn-nn-nn-nn-nn-nn.
0 = off, 1 = on. Default is 0.
01 = RS232/RS422 port on rear panel, 02 = front panel Config port
9600, 19200, 384000, or 115200
odd, even, none, mark, or space (only first letter required)
1 or 2
7 or 8
0 = RS-232, 1 = RS-422
Format nnn.nnn.nnn.nnn. Leading zeros in each field are optional.
Format nnn.nnn.nnn.nnn. Leading zeros in each field are optional.
HDXP Plus Series Switchers • Remote Configuration and Control
Response
Additional Description
(Switcher to Host)
X4% ]
Idh Set DHCP on or off (
X4% ]
View DHCP status
X2& ]
Ipi Set IP address
X2& ]
View the HDXP IP address.
X3$ ] View media access code
(MAC) address
unit.
Set subnet mask
X5* ]
Ips
HDXP.
X5* ]
View the subnet mask.
Set gateway IP address
X5( ]
Ipg
for the HDXP.
X5( ]
View the gateway address.
X3) ] Set administrator password
Ipa •
X3)
X3) ]
View current administrator
password.
] Remove all administrator and
Ipa •
user passwords.
X3) ]
Ipu • Set user password
HDXP.
X3) ] View the user password.
] Clear the user password only.
Ipu •
}
X4^ X4& X4* X4(
Cpn • Ccp , ,
Set baud rate
Data bits
X5)
port
X4& X4* X4( X5) ]
View the parameters of port
, , ,
X4^
X4^ X5! ]
Set the serial communication
Cpn • Cty
type
X5! ]
View mode
X4%
).
X4%
.
X2&
.
X3$
for your
X5*
for the
X5(
for the HDXP.
X3)
for the
X5) ]
,
X4& X4*
, parity ,
X4(
, and stop bits
for the IP connection for
X4^
.
.
X5! X4^
for serial port .
X5! X4^
of port .
63