Video Sockets - TANDBERG Codec 3000 MXP Reference Manual

Interfaces and Sockets – Codec 6000

Video Sockets

The system will S-video input
automatically
Main camera
adapt to a PAL or
NTSC input.
Single Dual
S-video output
Mini-DIN sockets
DVI-I pin-out
Pin
Note: TANDBERG supports DVI-D
Single-Link, DVI-A and DVI-I Sin-
gle-Link format cables.
DVI-D cables transmit digital
T.M.D.S. signals, DVI-A cables
transmit analogue VGA signals
and DVI-I cables can transmit
either digital or analogue signals.
If your DVI cable is not long
enough, use extension cables.
C1
Observe, however, that the
maximum cable length should not
C4
exceed 5 m to avoid quality loss.
D 13887.08
MAY 2008
MXP
Mini-DIN sockets Composite video input
Aux. camera Doc. camera
Single Dual
Composite video output
RCA sockets
DVI-I Pin-out
Assignment Pin Assignment
1 T.M.D.S. Data 2– 9 T.M.D.S. Data 1–
2 T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+
3 T.M.D.S. Data 2/4 11 T.M.D.S. Data 1/3
Shield Shield
4 T.M.D.S. Data 4– 12 T.M.D.S. Data 3–
5 T.M.D.S. Data 4+ 13 T.M.D.S. Data 3+
6 DDC Clock 14 +5 V power
7 DDC Data 15 GND
(return for +5 V,
HSync and Vsync)
8 Analogue Vertical 16 Hot plug detect
Sync
Analogue Red C2 Analogue Green
Analogue C5 Analogue GND
Horizontal Sync (analogue
R, G & B return)
RCA sockets PC DVI-I input
(Digital Video Interface,
VCR
Single Dual
DVI output
sockets
Pin Assignment
Formats supported on DVI-I out:
17 T.M.D.S. Data 0–
SVGA (800 × 600) 75 Hz
XGA (1024 × 768) 60 Hz
18 T.M.D.S. Data 0+
SXGA (1280 × 1024) 60 Hz
HD720p (1280 × 720) 50 Hz, 60 Hz
19 T.M.D.S. Data 0/5
WXGA (1280×768) 60 Hz
Shield
Formats supported on DVI-I in:
20 T.M.D.S. Data 5–
SVGA (800 × 600) 60 Hz, 72 Hz, 75 Hz, 85 Hz
21 T.M.D.S. Data 5+
XGA (1024 × 768) 60 Hz, 70 Hz, 75 Hz
SXGA (1280 × 1024) 60 Hz
22 T.M.D.S. Clock
HD720p (1280 × 720) 50 Hz, 60 Hz
Shield
Do as follows to get WXGA:
23 T.M.D.S. Clock+
1 VGA Out Quality must be set to Auto.
2 VGA Monitor Format
3 PC Picture Format
24 T.M.D.S. Clock–
If you are using TANDBERG supplied monitors this will give WXGA out
when displaying graphics.
C3 Analogue Blue
If non-TANDBERG provided displays are used, you must in addition
execute the command:
xConfiguration Video Outputs AllowWXGA: On
33
REFERENCE GUIDE FOR SYSTEM INTEGRATORS
sockets Note that the S-Video/Composite outputs on the
MXP
6000 are now by default turned off from
Integrated digital
factory.
and analogue)
Ref. xConfiguration Video Outputs TV [1..2] Mode
Levels
Composite: 1 Vpp, 75 W
S-Video (Y/C):
Y: 1 Vpp, 75 W
C (PAL): 0.3 Vpp, 75 W
C (NTSC): 0.28 Vpp, 75 W
must be set to Wide.
must be set to Normal.
TANDBERG 3000 MXP & 6000 MXP
S-video Mini-DIN pin-out
External view of socket
4
3
2
1
Pin 1: Ground (Luminance)
Pin 2: Ground (Chrominance)
Pin 3: Luminance (Y)
Pin 4: Chrominance (C)
RCA pin-out
External view of socket
Signal GND