Configuration Commands; Switch Control Commands - TANDBERG Codec 3000 MXP Reference Manual

TANDBERG Video Switch
Communicating with the Video Switch

Configuration Commands

Messages starting with 8x-01-40-<00..1f> are configuration commands.
Command Command Packet
SW_Port_0_Cfg 8x 01 40 00 ... ff
SW_Port_1_Cfg 8x 01 40 01 ... ff
SW_Port_2_Cfg 8x 01 40 02 0p ff
SW_Port_3_Cfg 8x 01 40 03 0p ff
SW_Port_x_ 8x 01 40 04 0p
Push_Cfg 0q 0r ff

Switch control commands

Messages starting with 8x-01-40-<20..3f> are switch control commands.
Command Set Command Packet
SW_Input_Set 8x 01 40 20 0p ff
Misc.
Command Command Packet
CAM_Boot 8x 01 42 ff
D 13887.08
MAY 2008
Comments
Currently not in use.
Currently not in use.
p=0: Disable this port
p=1: Enable this port as a secondary
VISCA chain port for cameras usually con-
nected to codec input 2-5 (default).
p=2: Use this port as a debug port.
p=0: Disable this port
p=1: Enable this port as a dual visca port
(default).
p=2: Use this port as a debug port.
Configure which push messages to send
for given port.
p=0/3: Configure port 0 or 3.
qr bit 0: Enable/disable SW_Input_Push.
qr bit 1: Enable/disable SW_Sync_Push.
qr bit 2: Enable/disable Enhanced VISCA.
qr = 00 is default for both ports.
Comments
Sets which input to use.
p=0..5
This will generate a SW_Input_Push on
the THSI Visca port if issued from the
dual visca port and vice versa.
Comments
Reboot the switch. This will also reset se-
rial speed to 9600.
Inquiries
Messages starting with 8x- 09...
Command set Command Packet
CAM_ID_Inq 8x 09 04 22 FF
CAM_SWID_Inq 8x 09 04 23 ff
SW_Input_Inq 8x 09 40 20 ff
SW_Sync_Inq 8x 09 40 e0 0p ff
SW_InputFor- 8x 09 40 e1 ff
mat_ Inq
Push Messages
Command set Push Message
SW_Input_Push x0 01 40 20 0p ff
SW_Sync_Push x0 01 40 e0 0p
0q ff
239
TANDBERG 3000 MXP
REFERENCE GUIDE FOR SYSTEM INTEGRATORS
Reply and comments
Reply: 90 50 zz xx 00 yy FF
zz xx = switch rev, zz=0x40 for TVS
yy = firmware rev
Reply: x0 50 [1-125 bytes SWID] ff.
Reply 90 50 0p ff
p=Active input, 0..5
Input: p=Input 0..5
Reply: 90 50 0p ff
p=2: Input has sync
p=3: No sync on input
Reply: 90 50 0p 0q ff
pq = Format for active input.
0 = 720p60
1 = 720p59.94
2 = 720p50
Comments
The input has been changed.
p = the new input source
Sync state has changed on an input.
This one will also be sent if the format is
changed, so if sync is on, send a SW_For-
mat_Inq.
p = source 0..5
q = state: 2 = sync, 3 = no sync
& 6000 MXP