Fluke 9100 User Handbook Manual page 250

Final Width = 215mm
10.4.7.8 Calibration of 'UUTi Low' Source Current Hardware Configuration
If both UUTi High source current and UUTi Low source current hardware configurations are being calibrated, the UUTi Low source
current calibrations shown in Table 10.4.7.3 below should be performed after the UUTi High source current calibrations. (See
Note [2] below)
Table 10.4.7.3: Resistance — 'UUTi Low' Source Current Hardware Configurations and Calibration Points
Output span Output
covered by to select
hardware hardware
configuration config. Default
40.001 100 60.000
to 400.000 300.000
0.40001k 1k 0.60000k
to 4.00000k 3.00000k
4.0001k 10k 6.0000k
to 40.0000k 30.0000k
40.001k 100k 60.000k
to 400.000k 300.000k
0.40000M 1M 0.60000M
to 4.00000M 3.00000M
4.0001M 10M 6.0000M
to 40.0000M 30.0000M
40.001M 100M 60.000M
to 400.000M 300.000M
Notes:
[2] Calibration of these UUTi Low source current hardware configurations may be omitted if the Standards DMM has no suitable range, as
they are automatically calibrated by internal transfers, to an accuracy greater than that obtainable using the majority of DMMs, when the
corresponding UUTi High source current hardware configurations are calibrated. (When the 4M UUTi High source current hardware
configuration is calibrated, the 4M UUTi Low source current hardware configuration is automatically calibrated. When the 40M UUTi
High source current hardware configuration is calibrated, the 40M and 400M UUTi Low source current hardware configurations are
automatically calibrated.)
If these UUTi Low source current hardware configurations are being calibrated against an external standard as detailed in the table above,
the calibration operations must be performed after the corresponding UUTi High source current hardware configurations have been
calibrated. Otherwise the calibration correction factors produced will be overwritten by those generated automatically by the UUTi High
source current calibrations.
10.4-42 Section 10: Calibrating the Model 9100: Resistance Function
Calibration Targets
Amplitude
Minimum Maximum Recommended
41.000 75.000 45.000
100.000 390.000 380.000
0.41000k 0.75000k 0.45000k
1.00000k 3.90000k 3.80000k
4.1000k 7.5000k 4.5000k
10.0000k 39.0000k 38.0000k
41.000k 75.000k 45.000k
100.000k 390.000k 380.000k
0.41000M 0.75000M 0.45000M
1.00000M 3.90000M 3.80000M
4.1000M 7.5000M 4.5000M
10.0000M 39.0000M 38.0000M
41.000M 75.000M 45.000M
100.000M 390.000M 380.000M
Factor
Number
Source Current
Minimum Maximum
50 A 200 A 1
50 A 200 A 2
50 A 200 A 1
50 A 200 A 2
5.0 A 20 A 1
5.0 A 20 A 2
500nA 2.0 A 1
500nA 2.0 A 2
50nA 200nA 1 [2]
50nA 200nA 2 [2]
5.0nA 20nA 1 [2]
5.0nA 20nA 2 [2]
5.0nA 20nA 1 [2]
5.0nA 20nA 2 [2]