Fluke 9100 User Handbook Manual page 248

Final Width = 215mm
10.4.7.6 Calibration Setup
1. Connections Ensure that the 9100 is connected to the Standards DMM as shown in Fig. 10.4.7.1, and that both instruments
are powered on and warmed up.
2. 9100 Select the Resistance Function by pressing the ' ' key on the right of the front panel.
10.4.7.7 Calibration of 'UUTi High' Source Current Hardware Configurations
If both UUTi High and UUTi Low source current hardware configurations are being calibrated, the UUTi High source current
calibrations shown in Table 10.4.7.2 below should be performed before the UUTi Low source current calibrations.
Table 10.4.7.2: Resistance — 'UUTi High' Source Current Hardware Configurations and Calibration Points
Output span Output
covered by to select
hardware hardware
configuration config. Default
00.0000 10 1.0000
to 40.0000 30.0000
40.001 100 60.000
to 400.000 300.000
0.40001k 1k 0.60000k
to 4.00000k 3.00000k
4.0001k 10k 6.0000k
to 40.0000k 30.0000k
40.001k 100k 60.000k
to 400.000k 300.000k
0.40000M 1M 0.60000M
to 4.00000M 3.00000M
4.0001M 10M 6.0000M
to 40.0000M 30.0000M
40.001M 100M 60.000M
to 400.000M 300.000M
Notes:
[1] This calibration point is limited by the maximum source current. If the actual source current is less than the indicated maximum, the output
value can be raised in inverse proportion. For example, a 50nA source current would allow the calibration point to be increased to 160M .
10.4-40 Section 10: Calibrating the Model 9100: Resistance Function
Calibration Targets
Amplitude
Minimum Maximum Recommended
0.0100 7.5000 0.1000
10.0000 39.0000 38.0000
41.000 75.000 45.000
100.000 390.000 380.000
0.41000k 0.75000k 0.45000k
1.00000k 3.90000k 1.95000k
4.1000k 7.5000k 4.5000k
10.0000k 39.0000k 38.0000k
41.000k 75.000k 45.000k
100.000k 390.000k 380.000k
0.41000M 0.75000M 0.45000M
1.00000M 3.90000M 3.80000M
4.1000M 7.5000M 4.5000M
10.0000M 39.0000M 38.0000M
41.000M 70.000M 45.000M
76.500M 390.000M 80.000M
Factor
Number
Source Current
Minimum Maximum
500 A 2.0mA 1
500 A 2.0mA 2
500 A 2.0mA 1
500 A 2.0mA 2
500 A 2.0mA 1
500 A 2.0mA 2
50 A 200 A 1
50 A 200 A 2
5.0 A 20 A 1
5.0 A 20 A 2
500nA 2.0 A 1
500nA 2.0 A 2
50nA 200nA 1
50nA 200nA 2
50nA 100nA 1
50nA 100nA 2
[1]