Smartgen HGM9510N User Manual page 56

No. Functions
12 Digi. input 1
13 Digi. input 2
14 Digi. input 3
15 Digi. input 4
16 Digi. input 5
17 Digi. input 6
18 Magnetic pickup shield
19 MP2
20 MP1
21 Digi. input 7
22
23 Digi. output 4
24
25 ECU TR
26 ECU CAN H
27 ECU CAN L
28 MSC(1) TR
29 MSC(1) CAN H
30 MSC(1) CAN L
31 GOV B(+)
32 GOV A(-)
33 AVR B(+)
34 AVR A(-)
35 RS485(1) TR
36 RS485(1) A(+)
37 RS485(1) B(-)
38
39 Digi. output 5
40
41
Digi. output 6
42
Bus A-phase voltage
43
input
Bus B-phase voltage
44
input
Bus C-phase voltage
45
input
46 Bus N-wire input
Genset A-phase voltage
47
input
Genset B-phase voltage
48
input
HGM9510N/HGM9530N Paralleled Genset Controller User Manual
Cable Size
1.0mm 2 Ground connected is active (B-).
1.0mm 2 Ground connected is active (B-).
2
1.0mm Ground connected is active (B-).
1.0mm 2 Ground connected is active (B-).
1.0mm 2 Ground connected is active (B-).
1.0mm 2 Ground connected is active (B-).
Connect with speed sensor, and shielding line is
2
0.5mm recommended. B- is already connected with speed
sensor input 2 in the inside controller.
1.0mm 2 Ground connected is active (B-).
Normally close output, rated 8A.
1.5mm 2 Public points of relay.
Normally open output, rated 8A.
/
Impedance-120Ω shielding wire is recommended, and
0.5mm 2 the single-end shall be earth connected. Short connect
TR with H and then connect to 120Ω terminal resistor.
0.5mm 2
/
Impedance-120Ω shielding wire is recommended, and
2
0.5mm the single-end shall be earth connected. Short connect
0.5mm 2 TR with H and then connect to 120Ω terminal resistor.
0.5mm 2
Shielding wire is recommended. Shielding layer shall be
0.5mm 2 earth connected at GOV end.
0.5mm 2 Shielding wire is recommended. Shielding layer shall be
2 earth connected at AVR end.
0.5mm
/
Impedance-120Ω shielding wire is recommended, and
0.5mm 2 the single-end shall be earth connected. Short connect
TR with A(+) and then connect to 120Ω terminal resistor.
0.5mm 2
2
1.5mm Normally close output, rated 8A.
1.5mm 2 Normally open output, rated 8A.
1.5mm 2 Public points of relay.
1.5mm 2 Normally open output, rated 8A.
1.5mm 2 Public points of relay.
1.0mm 2 Connect to A-phase of bus (2A fuse is recommended).
1.0mm 2 Connect to B-phase of bus (2A fuse is recommended).
1.0mm 2 Connect to C-phase of bus (2A fuse is recommended).
2
1.0mm Connect to N-wire of bus.
Connect
1.0mm 2
recommended).
Connect
2
1.0mm
recommended).
Remark
to A-phase of genset
to B-phase of genset
(2A fuse is
(2A fuse is
Page 56 of 116