Nice HySecurity SlideSmart DC Series Installation And Programming Manual page 12

UL 325 LISTING: Edge sensors and photo eyes must
be tested and labeled as "Recognized Components" or
otherwise certifi ed to UL 325 requirements in order to
be deemed acceptable for use in a gate operator. Study
Important Safety Instructions and consider your specifi c
325
installation to determine where greatest entrapment
risks exist. Locate edge sensors and/or photo sensors
accordingly. Be certain that a suffi cient number of sensors
are used so that pedestrians are protected from entrapment
Nice | HySecurity Recommended Sensors
in both directions of gate travel and all hazard areas are
fully protected. Most HySecurity gate operators require
Mfg. Part # or
external entrapment sensors that utilize Normally Closed
Model
(NC) contact means of monitoring. HySecurity gate
E3K-R10K4-NR-1
operators utilizing the SmartCNX Controller require external
Photo Eyes
entrapment sensors that have a 10k Ohm or 4-wire pulsed
NIR-50-325
(Retro
monitoring scheme. Refer to UL website at
-refl ective)
IRB-RET
most up-to-date list of gate operator safety standards (UL
E-931-S50RRGQ
325). Refer to www.astm.org
F2200 Gate and Fence Standards.
Blue Bus
Photo Eyes
Era Photo Eyes
(Thru-Beam)
OVS-50TNR
IRB-MON
E-960-D90GQ
Sentir Series
Edge
Sensors
CPT210-2U-#-T2
Hy2NC (Converts 10K
Edge Sensor
to NC Monitoring)
Converters
GEM103 (Converts 10K
to Pulsed Monitoring)
Edge
iGAZE RE Kit
Wireless
Kits
325
WEL-200
Multi-Input
Module
The Solution – MIM-62
UL 325 Standard:
Nice | HySecurity Recommended Sensors
• The operator shall monitor for the presence of every device at least once during each open and close cycle (32.1.8)
• It shall not be possible to make simple modifi cations in the fi eld by adding, suppressing or changing, either on the operator or external
Mfg. Part # or
entrapment protection device(s), to bypass, interfere with, or otherwise defeat the monitoring function. (32.1.10)
Model
• Entrapment zones are now defi ned for each gate type (4.23, 4.24, 4.29, 4.34)
E3K-R10K4-NR-1
Slide Gates: To enable fully automatic operation, all SLIDE gate operators will require a minimum of TWO monitored external
entrapment protection sensors (one for each direction) to protect entrapment zones in both the open and close direction of travel. Photo Eyes
NIR-50-325
(Retro
Preferred solution for slide gates: A photo eye for the close direction and a hard-wired edge sensor for the open direction that
-refl ective)
IRB-RET
is mounted to the face of the leading post of the fence behind the gate. (Reach through injuries are the most common hazard
associated with automatic sliding gates)
E-931-S50RRGQ
Swing Gates: To enable fully automatic operation, all SWING gate operators will require a minimum of ONE monitored external
entrapment protection sensor to protect entrapment zones in either the open or close direction of travel. However, an additional
monitored sensor is required if there is a risk of entrapment in both directions of gate travel.
Blue Bus
Preferred solution for swing gates: A photo eye for the close direction and/or a hard-wired wraparound edge sensor on the leading
Photo Eyes
Era Photo Eyes
edge of the gate, which protects for both directions of gate travel.
(Thru-Beam)
OVS-50TNR
IRB-MON
E-960-D90GQ
12 12
support.hysecurity.com
Recommended External Entrapment
Protection Sensors List
The following sensors have been tested with Nice | HySecurity gate operators by an
independent laboratory and certifi ed to comply with UL 325 7th Edition. Select sensors from this
list for UL compliant gate automation solutions. Contact the sensor manufacturer for specifi c
recommendations for use.
Brand
Omron MX000999
EMX -
www.ul.com
EMX -
Seco-Larm -
for a complete list of ASTM
EPMB/A
EPMOB/A
EPLOB/A
Nice | EPMAB/A
HySecurity EMBORB/A
Optex -
EMX MX3990
Seco-Larm -
"AS1502-*
ASO Safety AS1501-*"
Miller Edge -
Recommended External Entrapment
HySecurity MX4018
Protection Sensors List
Miller Edge -
Transmitter
The following sensors have been tested with Nice | HySecurity gate operators by an Solutions -
independent laboratory and certifi ed to comply with UL 325 7th Edition. Select sensors from this
EMX -
list for UL compliant gate automation solutions. Contact the sensor manufacturer for specifi c
recommendations for use.
Miller Edge -
Brand
Omron MX000999
EMX -
EMX -
Seco-Larm -
EPMB/A
EPMOB/A
EPLOB/A
Nice | EPMAB/A
HySecurity EMBORB/A
Optex -
EMX MX3990
Seco-Larm -
"AS1502-*
SAFETY REQUIREMENTS
Nice |
Max Smart
Hysecurity
Range Touch
Part #
40 ft •
45 ft •
for
53 ft •
46 ft •
45 ft
33 ft •
65 ft •
90 ft •
•
•
•
•
•
•
Nice |
Max Smart
Hysecurity
Range Touch
Part #
40 ft •
45 ft •
53 ft •
46 ft •
45 ft
33 ft •
65 ft •
90 ft •
Control Boards
Smart
SmartCNX 1050
DC
• •
• • •
• • •
• •
• •
•
• •
• •
• • •
• • •
•
•
• • •
• • •
• •
Control Boards
Smart
SmartCNX 1050
DC
• •
• • •
• • •
• •
• •
•
hysecurity.com | 800-321-9947
• •
• •
Mercury
310
•
•
•
•
•
•
•
•
•
•
•
Mercury
310
•
•
•
•
1 of 2
Page
•
•