Table of Contents
Advertisement
phase noise curve
70420A confidence test, 3-9
Phase Noise Customer Support, 21-1
Phase Noise Floor and Region of Validity, 18-3
Phase Noise Level of Various Agilent/HP Sources, 18-4
Phase Noise Measurement without Phase-Lock Loop, 8-6
PLL bandwidth, 6-16
PLL suppression, 5-27, 5-50
measuring, 5-27, 5-50
Plotter Pens, 5-57, 5-60, 15-10
power sensor connectors, A-10
preventive maintenance, A-1
printer
using, 15-7
printing screens, 15-7
Problem Solving, 15-13
PTR, 6-14
R
R input port
amplitude, 6-6
level, 8-10
system noise floor, 6-6
reference
selecting, 6-8
Reference Source, 15-3
noise level, 6-6
reference source
high noise floor, 15-15
noise level, 6-7, 6-8
selection, 6-5, 6-8
reliable accuracy, 20-2
Repeating the Measurement, 15-6
required equipment
first measurement, 3-3
residual measurement, 9-2
research
doing more, 15-6
residual measurement, 9-2
residual measurements, 9-1
Residual Noise, 8-2
residual noise
Calibration, 8-6
calibration, 8-6
mechanisms, 8-2
translation devices, 8-4
results
evaluating measurement, 15-2
exporting measurement, 5-60
outputing, 15-7
results, printing, 15-7
RF connectors, caring for, A-2
rf synthesizer
residual noise, 8-2
RF synthesizer using DCFM
defining the measurement, 5-11, 5-34, 7-49
S
segments
sweep, 5-28, 5-51
selecting a reference, 6-8
Selecting the VCO Source, 6-5
semi-rigid cable, 8-8
sensitivity, 6-11
setup considerations
microwave source, 7-101
RF Synthesizer using DCFM, 5-14, 5-37, 7-52
RF synthesizer using EFC, 7-77
signal generator
tuning, 6-15
tuning requirements, 6-9
using a, 6-9
Single-Sided Spur, 8-24
small angle line, 15-18
software
starting the, 3-4
starting the measurement, 3-4
software updates, 21-2
source
adding using the asset manager, 5-3
specifications, 20-2
Specifying Your VCO Source, 6-5
Spur List, 15-16
spurs, 15-16
forest, 15-16
marking criterion, 15-16
omitting, 5-57
Stable RF Oscillator, 7-2
stable RF oscillator measurement, 7-2
Starting the Measurement Software, 5-2
starting the measurement software, 3-4
stop measurement, 5-28, 5-51
summary
parameter, 15-12
sweep-segments, 5-28, 5-51
system requirements, 2-4
System Specifications, 20-1
T
testing
Agilent/HP 8644B internal/external 10 MHz, 5-56
the Agilent/HP 8663A internal/external 10 MHz, 5-10
Three Source Comparison, 15-3
training guideslines, 1-3
translation devices, 8-4
Tune Range of VCO vs. Center Voltage, 18-9
tuning, 20-2
Signal Generators, 6-15
Tuning Constant, 6-11
entering Parameters, 7-73, 7-98, 9-3, 11-5, 11-20, 13-3, 14-2,
14-6
estimating, 7-73, 7-98, 9-3, 11-5, 11-20, 13-3, 14-2, 14-6
tuning constant
estimating, 6-11
Agilent Technologies E5500 Phase Noise Measurement System -iii
Advertisement
Table of Contents
