List Of System Halt - MIMAKI JV300-130 Maintenance Manual

MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of SYSTEM HALT
Model JV300-130/160 Issued 2014.05.30 Revised

7.1.4 List of SYSTEM HALT

 List of SYSTEM HALT (1/5)
No. LCD
SYSTEM HALT (*)
F-ROM CLEAR error (F-ROM clear unable)
10e :FROM CLEAR
F-ROM is not clearable on Parameter
1
writing, FW down loading and Log clearing.
(fls_secclr)
SYSTEM HALT (*)
FROM WRITE error (F-ROM writing
10f : FROM WRITE
unable)
2 F-ROM is not clearable on Parameter
writing, FW down loading and Log clearing.
(fls_secclr)
SYSTEM HALT (*)
No Keyboard PCB
110 : PCB KEY
3
SYSTEM HALT (*)
No CART IO PCB
112 :
4
SYSTEM HALT (*)
No PRAM
5
122 : PRAM NONE
SYSTEM HALT (*)
PRAM data error
6
123 : PRAM DATA
SYSTEM HALT (*)
PRAM address error
7
124 : PRAM ADDR
SYSTEM HALT (*)
EEPROM read trouble
8
125 : EEPROM READ
CIO Register (EER:Address 74) bit6
SYSTEM HALT (*)
EEPROM write trouble
126 : EEPROM WR
CIO Register (EER:Address 74) bit7
9
SYSTEM HALT (*)
Power OFF detection error (Not to OFF)
127 : POWER OFF
Power OFF process is conducted in the
Power ON/OFF control without pushing
down the sub-power SW.
10
SYSTEM HALT (*)
DALLAS IC BUSY error
147 : DS-IC BUSY
11
SYSTEM HALT (*)
COM Voltage is abnormal
189 : COM VOLT
12
© 2014 MIMAKI ENGINEERING CO.,LTD.
F/W ver
Cause
1. Execute the memory check (F-ROM) of [#TEST].
2. Upload the parameter and initialize all parameters with
[#PARAMETER].
3. Replace the MAIN PCB with a new one.
1. Execute the memory check (F-ROM) of [#TEST].
2. Upload the parameter and initialize all parameters with
[#PARAMETER].
3. Replace the MAIN PCB with a new one.
1. Check the connections between the Keyboard PCB and
the MAIN PCB and then disconnect and connect the
FFCs.
2. Replace the FFCs of the above routes.
3. Replace the Keyboard PCB with a new one.
4. Replace the MAIN PCB with a new one.
1. Check the connections between the COM32IO PCB
and the CART IO PCB, and then disconnect and
connect the FFCs.
2. Replace the FFCs and the cabeles of the above routes.
3. Replace the CART IO PCB with a new one.
4. Replace the COM32IO PCB with a new one.
1. Update F/W.
2. Replace the PRAM PCB with a new one.
3. Replace the MAIN PCB with a new one.
1. Update F/W.
2. Check the connection state between SL2H PCB - Head
memory PCB.
3. Replace the Head memory PCB with a new one.
4. Check the connection state between SL2H PCB -
MAIN PCB.
5. Replace the SL2H PCB with a new one.
6. Replace the MAIN PCB with a new one.
1. Check the connections between the Keyboard PCB
and the MAIN PCB.
2. Check the connector connection of DC Power Supply
(42V).
3. Check if there is no error on the power path from the
AC Inlet.
4. Replace the DC Power Supply(42V) with a new one.
5. Replace the Keyboard PCB with a new one.
6. Replace the MAIN PCB with a new one.
1. Check connection of the ID Contact PCB connection
cable and damage of the cable.
2. Try to use a different cartridge.
3. Replace the ID Contact PCB Assy. with a new one.
( See 6.4.14)
4. Replace the CART IO PCB with a new one.
1. Replace the HDC PCB with a new one.
2. Check the connections between the HDC PCB and the
Print head.
1.10 Remark
Corrective Measures
Rev.
1.0
( See 3.3.1)
1
( See 3.3.1)
2
( See 3.3.1)
3
4
( See 3.3.1)
5
( See 3.3.1)
6
7
( See 3.3.1)
8
7.1.4 R.1.0 P.1