List Of Warning Messages - MIMAKI JV300-130 Maintenance Manual

MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of Warning Messages
Model JV300-130/160 Issued 2014.05.30 Revised

7.1.3 List of Warning Messages

 List of Warning Messages (1/3)
No Message
.
List of Ink Error (Checking by guidance)
WRONG INK IC
1 IC chip of Ink Cartridge
unreadable properly
INK TYPE
2 Type of inserted Ink Cartridge
is different.
INK COLOR
3 The color of Ink Cartridge
inserted is different from the
color to be set.
WRONG CARTRIDGE
4 An error occurred in the IC
chip information of the ink
cartridge.
NO CARTRDG
5 No cartridge (Cartridge is not
installed)
INK END
6 Ink end (No ink left)
INK NEAR END
7 Ink near end (A small amount
of ink left)
EXPIRATION
8 Some ink cartridges are
expired.
EXPIRATION(1MONTH)
9 Some ink cartridges are
expired.
(One month has passed after
the expiration date.)
EXPIRATION(2MONTH)
10 Some ink cartridges are
expired.
(Two months have passed
after the expiration date.)
© 2014 MIMAKI ENGINEERING CO.,LTD.
Cause
1. Check the attached status of the chip.
2. Perform [#TEST][CHECK INK IC].
3. Replace the ID Contact PCB Assy. with a new one.
1. Check the type of the ink cartridge.
1. Check the color of the ink cartridge.
The chip was used too much (exceeding the specified times).
1. Check whether the chip was also replaced when the pack was
replaced.
2. Check the W ink nozzle clogging and resolve it.
3. Replace the chip.
(When the message is still displayed even after a Ink Cartridge is
charged;)
1. Execute and confirm [#TEST][SENSOR][CartridgeSensor](The
number meets the cartridge No.).
2. Check the peripheral and the assembly of the Presence Sensor.
3. Check the connection of the Presence Sensor and the End Sensor
4. .Replace the Cartridge with a new one
5. Replace the MAIN PCB with a new one.
(When the message is still displayed even after a new Ink Cartridge or an
empty Ink Cartridge is charged;)
1. Execute and confirm [#TEST][SENSOR][CartridgeSensor](The
number meets the cartridge
2. Check the peripheral and the assembly of the End Sensor.
3. Check the connection of the Presence Sensor and the Near End
Sensor.
4. Replace the Cartridge with a new one
5. Replace the MAIN PCB with a new one.
1. Be careful that the expiration date is coming soon. You can use up to
the two month later.
(If this message appears when a correct cartridge is set)
2. Check the clock time of the machine.
3. Check the assembly of the ID Contact PCB and the shape of the
contact plate, and execute the cleaning.
4. Check the connection of the ID Contact PCB.
5. Replace the Cartridge with a new one.
6. Replace the ID Contact PCB Assy. with a new one.
7. Replace the CART IO PCB with a new one.
1. Be careful that the expiration date is coming soon. You can use up to
the next month. The red LED blinks.
(If this message appears when a correct cartridge is set)
2. Check the assembly of the ID Contact PCB and the shape of the
contact plate, and execute the cleaning.
3. Check the connection of the ID Contact PCB.
4. Replace the Cartridge with a new one.
5. Replace the ID Contact PCB Assy. with a new one.
Replace the cartridge with the warning.
F/W ver 1.10 Remark
Corrective Measures
No.).
Rev.
1.0
1
( See 6.4.14)
2
3
4
( See 3.3.1)
5
( See 3.3.1)
6
7
8
( See 6.4.14)
7.1.3 R.1.0 P.1