Mitsubishi Electric NZ2GN2S1-16D User Manual page 90

NZ2GNCE3-32DT DC input/transistor output module
Item
Input specifications
Number of input points
Rated input voltage
Rated input current
Maximum number of simultaneous input points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
Input response time
Wiring method for common
Output specifications
Number of output points
Rated load voltage
Max. load current
Maximum inrush current
Leakage current at OFF
Max. voltage drop at ON
Output response time
Surge suppressor
External power supply for
output part
Protection function
Wiring method for common
Common specifications
Station type
Authentication Class
Network topology
Withstand voltage
Insulation resistance
*3
Noise immunity
Protection degree
External interface
Applicable wire size
Multicast filter
Cyclic transmission
3 SPECIFICATIONS
88
3.3 Performance Specifications
NZ2GNCE3-32DT
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
6.6mA TYP. (for 24VDC)
100%
11VDC or more/4mA or more
5VDC or less/1.5mA or less
3.3k
OFF  ON
0ms
(Factory default: 1ms)
ON  OFF
16 points/common (3-wire, sensor connector (e-CON) type)
Positive common type
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
0.5A/point, 4A/common
Current is limited by the overload protection function.
0.1mA or less
0.3VDC (TYP.) 0.5A, 0.6VDC (MAX.) 0.5A
OFF  ON
0.1ms or less
ON  OFF
0.8ms or less (resistive load)
Zener diode
Voltage 24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
Current 25mA or less (TYP. 24VDC per common) External load current is not included.
Overload protection Limited current when detecting overcurrent: 1.5 to 3.5A/point
function Activated to each point.
Overheat protection Activated to each point.
function
16 points/common (3-wire, sensor connector (e-CON) type)
Sink type
Remote station
Authentication Class B
Line topology, star topology, mixture of star topology and line topology, ring topology
510VAC for 1 minute between all DC external terminals and ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator
condition)
IP2X
Communication part RJ45 connector
Module power supply part One-touch connector for power supply and FG (5 pins, crimping type)
I/O part Sensor connector (e-CON) (4 pins, crimping type)
For power supply 0.66 to 0.98 (18 AWG)
[Finishing outer diameter: 2.2 to 3.0mm (A6CON-PW5P), 2.0 to 2.3mm (A6CON-PW5P-SOD)]
Strand diameter: 0.16mm or longer
Insulating coating material: PVC (heat resistant vinyl)
For I/O Sensor connector (e-CON)
The size depends on the connector plug used (sold separately). ( Page 146 Wiring of sensor
connector (e-CON))
Available
RX/RY points 32 points
RWr/RWw points 4 points
*2
/0.2ms/1ms/1.5ms/5ms/10ms/20ms/70ms
*1
*4
*1