Mitsubishi Electric NZ2GN2S1-16D User Manual page 102

NZ2GN2B1-32DTE DC input/transistor output module
Item
Input specifications
Number of input points
Rated input voltage
Rated input current
Maximum number of simultaneous input points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
Input response time
Wiring method for common
Output specifications
Number of output points
Rated load voltage
Max. load current
Maximum inrush current
Leakage current at OFF
Max. voltage drop at ON
Output response time
Surge suppressor
External power supply for
output part
Protection function
Wiring method for common
Common specifications
Station type
Authentication Class
Network topology
Withstand voltage
Insulation resistance
*3
Noise immunity
Protection degree
External interface
Applicable wire size
Applicable solderless
terminal
Multicast filter
Cyclic transmission
3 SPECIFICATIONS
100
3.3 Performance Specifications
NZ2GN2B1-32DTE
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
6.0mA TYP. (for 24VDC)
100%
11VDC or more/4mA or more
5VDC or less/1.5mA or less
3.3k
*2
OFF  ON
0ms
(Factory default: 1ms)
ON  OFF
16 points/common (Common terminal: terminal number 34) (1-wire, screw terminal block type)
Negative common type
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
0.5A/point, 4A/common
Current is limited by the overload protection function.
0.1mA or less
0.5VDC (TYP.) 0.5A, 0.8VDC (MAX.) 0.5A
OFF  ON
0.5ms or less
ON  OFF
1.0ms or less (resistive load)
Zener diode
Voltage 24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
Current 45mA or less (TYP. 24VDC per common) External load current is not included.
Overload protection Limited current when detecting overcurrent: 1.5A or more/point
function Activated to each point.
Overheat protection Activated to each point.
function
16 points/common (Common terminal: terminal number 33) (1-wire, screw terminal block type)
Source type
Remote station
Authentication Class B
Line topology, star topology, mixture of star topology and line topology, ring topology
510VAC for 1 minute between all DC external terminals and ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator
condition)
IP2X
Communication part RJ45 connector
Module power supply part Terminal block for module power supply and FG (2-piece spring clamp terminal block)
I/O part 34-point two-piece terminal block
Tightening torque range for terminal screw (M3  5.2 screw): 0.43 to 0.57Nm
Tightening torque range for terminal block mounting screw (M3.5 screw): 0.68 to 0.92Nm
Stranded wire: 0.3 to 1.5 (22 to 16 AWG), terminal slot size: 2.4mm  1.5mm
For power supply
For I/O Stranded wire: 0.3 to 2.0 (22 to 14 AWG)
Page 127 Applicable solderless terminal
Terminal block for module
*5
power supply and FG
Page 139 Applicable solderless terminal
I/O terminal block
Available
RX/RY points 32 points
RWr/RWw points 4 points
/0.2ms/1ms/1.5ms/5ms/10ms/20ms/70ms
*1
*6
*1
*4