Mitsubishi Electric NZ2GN2S1-16D User Manual page 55

NZ2GN2B1-16T transistor output module
Item
Station type
Authentication Class
Network topology
Number of output points
Rated load voltage
Max. load current
Maximum inrush current
Leakage current at OFF
Max. voltage drop at ON
OFF  ON
Output response time
ON  OFF
Surge suppressor
External power supply for Voltage
output part
Current
Withstand voltage
Insulation resistance
Noise immunity
Protection degree
Wiring method for common
Protection function Overload protection
function
Overheat protection
function
External interface Communication part
Module power supply part
I/O part
Applicable wire size For power supply
For I/O
Applicable solderless Terminal block for module
terminal power supply and FG
Terminal block for output
Multicast filter
Cyclic transmission RX/RY points
RWr/RWw points
Module power supply Voltage
Current
Weight
*1 Use bar solderless terminals for wiring.
*2 Only one wire can be inserted into a wire insertion opening for the terminal block for module power supply and FG. Multiple wires cannot
be connected to a terminal. Connecting two or more wires may cause a poor contact.
*3 This value indicates the number of points set by default when the module is dragged and dropped to the network map in the CC-Link IE
TSN Configuration window. According to the function used, set an appropriate number of points. ( Page 226 Output module (16-
point module))
NZ2GN2B1-16T
Remote station
Authentication Class B
Line topology, star topology, mixture of star topology and line topology, ring topology
16 points
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
0.5A/point, 4A/common
Current is limited by the overload protection function.
0.1mA or less
0.3VDC (TYP.) 0.5A, 0.6VDC (MAX.) 0.5A
0.1ms or less
0.8ms or less (resistive load)
Zener diode
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
40mA or less (TYP. 24VDC per common) External load current is not included.
510VAC for 1 minute between all DC external terminals and ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator
condition)
IP2X
16 points/common (Common terminal: terminal number 18) (1-wire, screw terminal block type)
Sink type
Limited current when detecting overcurrent: 1.5 to 3.5A/point
Activated to each point.
Activated to each point.
RJ45 connector
Terminal block for module power supply and FG (2-piece spring clamp terminal block)
18-point two-piece terminal block
Tightening torque range for terminal screw (M3  5.2 screw): 0.43 to 0.57Nm
Tightening torque range for terminal block mounting screw (M3.5 screw): 0.68 to 0.92Nm
Stranded wire: 0.3 to 1.5 (22 to 16 AWG), terminal slot size: 2.4mm  1.5mm
Stranded wire: 0.3 to 2.0 (22 to 14 AWG)
Page 127 Applicable solderless terminal
*2
Page 139 Applicable solderless terminal
Available
16 points
*3
4 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
110mA or less (24VDC, all points ON)
0.21kg
*1
3 SPECIFICATIONS
3.3 Performance Specifications
3
53