Mitsubishi Electric NZ2GN2S1-16D User Manual page 33

NZ2GN2B1-32D DC input module
Item
Station type
Authentication Class
Network topology
Number of input points
Rated input voltage
Rated input current
Maximum number of simultaneous input points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
OFF  ON
Input response time
ON  OFF
Withstand voltage
Insulation resistance
*3
Noise immunity
Protection degree
Wiring method for common
External interface Communication part
Module power supply part
I/O part
Applicable wire size For power supply
For I/O
Applicable solderless Terminal block for module
terminal power supply and FG
Terminal block for input
Multicast filter
Cyclic transmission RX/RY points
RWr/RWw points
Module power supply Voltage
Current
Weight
*1 The performance specifications vary depending on firmware versions of modules used. ( Page 256 Added and Changed Functions)
*2 If the input response time is set to "0ms", the actual input response time is 80s at OFF  ON, and 160s at ON  OFF.
*3 It is the noise immunity of when the input response time setting value is other than "0ms". Note that the module is easily affected by
noise if "0ms" is set.
*4 Use bar solderless terminals for wiring.
*5 Only one wire can be inserted into a wire insertion opening for the terminal block for module power supply and FG. Multiple wires cannot
be connected to a terminal. Connecting two or more wires may cause a poor contact.
*6 This value indicates the number of points set by default when the module is dragged and dropped to the network map in the CC-Link IE
TSN Configuration window. According to the function used, set an appropriate number of points. ( Page 225 Input module (32-point
module))
NZ2GN2B1-32D
Remote station
Authentication Class B
Line topology, star topology, mixture of star topology and line topology, ring topology
32 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
6.0mA TYP. (for 24VDC)
100%
11VDC or more/4mA or more
5VDC or less/1.5mA or less
3.3k
*2
0ms /0.2ms/1ms/1.5ms/5ms/10ms/20ms/70ms
(Factory default: 1ms)
510VAC for 1 minute between all DC external terminals and ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator
condition)
IP2X
32 points/common (Common terminal: terminal number 33, 34) (1-wire, screw terminal block type)
Positive common/negative common shared type
RJ45 connector
Terminal block for module power supply and FG (2-piece spring clamp terminal block)
34-point two-piece terminal block
Tightening torque range for terminal screw (M3  5.2 screw): 0.43 to 0.57Nm
Tightening torque range for terminal block mounting screw (M3.5 screw): 0.68 to 0.92Nm
Stranded wire: 0.3 to 1.5 (22 to 16 AWG), terminal slot size: 2.4mm  1.5mm
Stranded wire: 0.3 to 2.0 (22 to 14 AWG)
Page 127 Applicable solderless terminal
*5
Page 139 Applicable solderless terminal
*1
Available
32 points
*6
4 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
110mA or less (24VDC, all points ON)
0.31kg
*1
*4
3 SPECIFICATIONS
3.3 Performance Specifications
3
31