Edid Management; Understanding The Edid; Advanced Edid Management - Lightware HDMI-TPS-RX110AY Series User Manual


  
10. Technologies
10.1. EDID Management
10.1.1. Understanding the EDID
The Extended Display Identification Data (EDID) is the passport of display devices (monitors, TV sets,
projectors). It contains information about the capabilities of the display, such as supported resolutions,
refresh rates (these are called Detailed Timings), the type and manufacturer of the display device, etc.
After connecting a source to a display (DVI, HDMI, DP), the source reads out the EDID to determine the
resolution and refresh rate of the image to be transmitted.
Most DVI computer displays have 128-byte long EDID structure. However, Digital Televisions and HDMI
capable displays may have another 128 bytes, which is called E-EDID and defined by CEA (Consumer
Electronics Association). This extension contains information about additional Detailed Timings, audio
capabilities, speaker allocation and HDMI capabilities. It is important to know that all HDMI capable devices
must have CEA extension, but not all devices with CEA extension are HDMI capable.
Common Problems Related to EDID
Problem: "Mysystemconsistsofthefollowing:acomputer,aLightwaredevice,aWUXGA(1920x1200)
LCDmonitor,andanSXGA(1280x1024)projector.Iwouldliketoseethesameimageonthe
monitorandtheprojector.WhatEDIDshouldIchooseontheLightwaredevice?"
Solution: Ifyouwanttoseetheimageonbothdisplays,youneedtoselecttheresolutionofthesmaller
display (in this case SXGA), otherwise the smaller display may not show the higher resolution
image.
Problem: "IhavechangedtoadifferentEDIDonaninputportoftheLightwaredevicetohaveadifferent
resolutionbutnothinghappens."
Solution: SomegraphicscardsandvideosourcesreadouttheEDIDonlyafterpower-upandlatertheydo
not sense that EDID has been changed. You need to restart your source to make it read out the
EDID again.
EDID Communication
Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3
HDMI-TPS-RX110AY series – User's Manual
10.1.2. Advanced EDID Management
Each DVI sink (e.g. monitors, projectors, plasma displays, etc...) must support the EDID data structure.
Source BIOS and operating systems are likely to query the sink using DDC2B protocol to determine what
pixelformatsandinterfacearesupported.DVIstandardusesEDIDdatastructuretoidentifythemonitortype
andcapabilities.MostDVIsources(VGAcards,settopboxes,etc.)willoutputDVIsignalafteracceptingthe
connected sink's EDID information. In the case of EDID readout failure or missing EDID, the source will not
outputDVIvideosignal.
Lightware devices provide the Advanced EDID Management function that helps system integration. The
built-in EDID Router can store and emulate factory pre-programmed- and User programmable EDIDs. The
EDID of the attached monitors or projectors for each output are stored in a non-volatile memory. This way
the EDID of a monitor is available when the monitor is unplugged or switched off.
Any EDID can be emulated on any input. An emulated EDID can be copied from the EDID router's memory
(static EDID emulation), or from the last attached monitor's memory (dynamic EDID emulation). For example,
theLightwaredevicecanbesetuptoemulateasinkdevice,whichisconnectedtooneoftheoutputs.In
this case, the EDID automatically changes, if the monitor is replaced with another display device (as long as
it has a valid EDID).
EDID is independently programmable for all inputs without affecting each other. All inputs have their own
EDID circuit.

INFO: The user is not required to disconnect the video cable to change an EDID as opposed to other
manufacturer's products. EDID can be changed even if a source is connected to the input and powered
ON.

INFO: WhenEDIDhasbeenchanged,theroutertogglestheHOTPLUGsignalfor2seconds.Somesources
do not sense this signal. In such cases, the source device must be restarted or powered OFF and ON
again.
106