Clear One Or More Event(S); Export And Import Events; Event Creating - Example - Lightware HDMI-TPS-RX110AY Series User Manual


  
5.SoftwareControl-LightwareDeviceController
5.8.4. Clear One or More Event(s)
Clear an Event
Press the Clear button in the Event list or in the header section in the Event editor.
Clear all Events
WhenalltheEventsmustbeclearedpresstheLoad factory defaults button above the Event list. You will be
promptedtoconfirmtheprocess.
5.8.5. Export and Import Events
ThefeatureallowssavingalltheEvents.ThebackupfilecanbeuploadedtoanotherHDMI-TPS-RX110AY
receiver.
Export all the Events
Step 1. Press the Export button above the Event list.
Step 2. TheSaveasdialogboxwillappear.Setthedesiredfolderandfilename,thenpresstheSave button.
ThegeneratedfileisasimpletextfilewhichcontainsLW3protocolcommands.Thefilecanbeviewedbya
simple text editor, e.g. Notepad.
ATTENTION!
Editingthefileisrecommendedonlyforexpertusers.
Import all the Events
Step 1. Press the Import button above the Event list.
Step 2. TheOpendialogboxwillappear.Selectthedesiredfolderandfile,thenpresstheOpen button.
5.8.6. Event Creating - Example
The following example shows you on a real-life situation how to set up an Event.
The Concept
The HDMI-TPS-RX110AY receiver
is connected to a projector by the
HDMI output port. The receiver is
also connected to the projector
by the RS-232 port and can send
commands via the serial line.
The task is to turn on the projector
when signal is detected on the
HDMI output port.
RS-232 Settings
Make sure that the serial line is established between the receiver and the projector. Check that the RS-232
settingsofthereceiverissetexactlythesamewhichrequiredfortheprojector:baudrate,databits,parity,
stopbits.Thereceiverneedstobesetto:Controlprotocol:LW3;andRS-232mode:Pass-through.Seethe
relevantLDCsettingsintheRS-232 section.
HDMI-TPS-RX110AYseries–User'sManual
Setting the Event
YoucancreatetheEventintheWizardinfewsimple
steps:
Step 1. Set the condition.
Selecttherequiredparameterstosetthecondition:
▪
▪
▪
Click on the Apply button to complete the procedure.
Whenitisdone,theconditionappearsontheupper
sideintextualandLW3commandformataswell.
Step 2. Set the action.
Iftheconditionisfulfilled,thefollowingactionneeds
to be launched: the receiver sends a command to
theprojectorovertheserialline:
▪
For this instance the command has to be closed
with the <CR><LF> characters so they need to be
escaped. You can use the following format for
escaping:
<command
Inthecurrentcasethecommandis:PWR0\x0d\x0a
Selecttherequiredparameterstosettheaction:
▪
▪
▪
▪
Step 3. Enable the Event.
Select the E1 enabled pipe in upper left corner to set the Event as launched.
INFO:

intheWizardwheretheentireLW3structuretreeisavailable.Forexampleinsteadofsignaldetectionyou
cansetaspecifiedresolutionorcolorrangeeitherasacondition.
Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3
Category:Video;
Expression:Signalisdetectedonaport;
Port:O1.
Power on - the required command which is
acceptedbytheprojector:PWR0<CR><LF>
><\x0d\x0a><command ><\x0d\x0a>...
1 2
...<command ><\x0d\x0a>
n
Category:RS-232;
Expression:SendRS-232message;
Port:P1;
Message:PWR0\x0d\x0a
Ifyoudonotfindtherequiredcategory/expression/etcwhatyouneed,choosetheAdvancedmode
45